Starting systems: starter motors and circuits – Motor Vehicle Theory motor mechanics lesson
Lesson 97 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out how a starter motor turns a cold engine, how the solenoid and one-way clutch work, and why the starting circuit carries the biggest current in the car.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
The lesson covers gear ratios and Ohm's law in the starting circuit. Cranking an engine is dangerous near moving parts, so all practical work belongs in a supervised workshop. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Some hybrid cars have no conventional starter motor at all. How might they start the engine, and what are the advantages?”
- Later: the homework, then the practice test.
Watch out for
- Thinking a click with no cranking means the starter motor itself has failed. A click shows the solenoid is moving. The cause is often a flat battery or high resistance in the main cables, which a technician checks first.
- Thinking the ignition switch carries the starter current. The switch only operates the solenoid (often through a relay). The solenoid's heavy contacts carry the cranking current.
- Thinking the starter stays engaged while the engine runs. The pinion is pulled out of mesh when the key is released, and the one-way clutch protects the motor in the moment the engine fires.
Hands-on: Make a gear model with two card circles: one with 10 notches (the pinion) and one with 120 (the ring gear). Mark a dot on each. Turn the small one and count how many turns it takes to make the big one go round once. Work out the ratio and use it to estimate cranking speed if the starter turns at 2,000 rpm. Card and paper only.
What you will learn
- I can describe the starting circuit: battery, ignition switch, safety switch, solenoid and motor.
- I can explain how a pre-engaged starter engages and disengages the flywheel ring gear.
- I can calculate the gear ratio between pinion and ring gear and the resulting engine cranking speed.
- I can relate common symptoms to likely starting system faults.
Key words
- starter motor
- A powerful DC electric motor that turns the engine fast enough for it to start.
- solenoid
- An electromagnetic switch on the starter that pushes the pinion into mesh and closes the heavy main contacts.
- pinion
- The small gear on the starter shaft that meshes with the ring gear on the flywheel.
- ring gear
- The large toothed ring around the engine's flywheel (or flexplate) that the pinion drives.
- one-way (overrunning) clutch
- A clutch in the starter drive that lets the pinion drive the engine but freewheels once the engine runs faster than the starter.
The big ideas
An engine cannot start itself. It must be turned fast enough to draw in air and fuel, compress them and fire. Turning a cold engine against its compression and thick oil takes a lot of power, so the starter motor draws the largest current of anything on a conventional car, often well over a hundred amps.
The starting system is designed around that huge current. A small ignition switch controls a solenoid, which acts as a heavy-duty relay. Short, thick cables connect the battery to the starter and the engine back to the battery through the earth strap.
Modern cars add safety interlocks, so the engine can only be cranked in neutral or park, or with the clutch pressed, and an immobiliser that blocks starting without the right key. This lesson explains how the system works; testing it is work for a trained technician.
Read-through: the teaching steps
The starting circuit
There are two circuits:
- The control circuit – ignition switch (or start button and control unit), a safety switch (clutch pedal switch on a manual, park/neutral switch on an automatic), often a starter relay, and the solenoid's windings. It carries a few amps.
- The main circuit – the heavy battery cable to the solenoid's main terminal, the contacts inside the solenoid, the motor, and back through the engine and earth strap. It carries the cranking current.
Because the current is so high, even a small resistance in the main circuit causes a large voltage drop and slow cranking.
The motor
Starter motors are DC motors designed for very high torque at low speed for a few seconds at a time.
- Older designs used series-wound field coils, which give maximum torque at standstill.
- Many modern starters use permanent magnets and a small internal reduction gear set, making them lighter and smaller for the same torque.
Current reaches the spinning armature through carbon brushes on a commutator. Starters are not designed for long use: cranking for long periods overheats them.
The pre-engaged starter and solenoid
Most starters are pre-engaged: the pinion meshes with the ring gear before the motor turns at full power.
- Turning the key energises two solenoid windings: a heavy pull-in winding and a lighter hold-in winding.
- The solenoid plunger moves, and a lever pushes the pinion along the shaft into mesh.
- At the end of its travel the plunger closes the main contacts, and full current flows to the motor.
- The pull-in winding is now shorted out; the hold-in winding keeps the plunger in.
- Releasing the key de-energises the solenoid; a spring pulls the pinion out of mesh.
The one-way clutch and gearing
When the engine fires, it may try to spin the pinion far faster than the starter can safely turn. A one-way (roller) clutch between the motor shaft and the pinion lets the pinion freewheel, protecting the motor.
The pinion has far fewer teeth than the ring gear, giving a large gear reduction. Ratio = ring gear teeth ÷ pinion teeth. A typical ratio is around 10:1 to 15:1, so a starter turning at a couple of thousand rpm cranks the engine at a couple of hundred rpm with much more torque.
Stop-start and other designs
Stop-start vehicles restart the engine many times on every journey. They use strengthened starters, or a belt-driven motor-alternator unit that restarts the engine through the auxiliary belt. Hybrid vehicles often start the engine with their high-voltage motor; HSE says that high-voltage system (up to 650 V DC on current vehicles) is for trained technicians only.
Symptoms and likely causes
A technician uses the symptoms as clues, then confirms with tests from the manufacturer's information:
- Nothing happens – flat battery, failed safety switch, immobiliser, control circuit fault, or a failed solenoid.
- A single click – the solenoid works but little current reaches the motor: flat battery, high-resistance cable or earth, burnt solenoid contacts.
- Slow cranking – weak battery, high resistance in the main circuit, or a worn motor.
- Whirring with no cranking – pinion not engaging or one-way clutch slipping.
- Grinding – damaged pinion or ring gear teeth.
The starter turns the engine, so testing is done by a qualified person with the vehicle secured, never by someone leaning into the engine bay.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Electrical and electronic systems lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- US Department of Energy, Alternative Fuels Data Center – How do gasoline cars work?
- HSE – Electric and hybrid vehicles
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.