Charging systems: alternators and regulation – Motor Vehicle Theory motor mechanics lesson
Lesson 96 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out how an alternator turns engine power into electricity, how its AC output becomes DC, how the regulator controls the voltage, and what the charge warning light is telling the driver.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
The lesson uses ratios and P = V × I. It explains how charging systems work; checking or testing a real charging system is done in a supervised workshop by a qualified person. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Smart charging changes the alternator's output to save fuel. What are the advantages and what could go wrong if the battery fitted is the wrong type?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the battery powers the car while the engine runs. Once the engine is running, the alternator supplies the loads and recharges the battery. The battery only helps if the loads exceed the alternator's output.
- Thinking an alternator makes DC directly. It makes three-phase AC in the stator. The rectifier diodes convert it to DC.
- Thinking a higher voltage is always better for charging. Too high a voltage overcharges the battery and can damage electronics. The regulator holds it near the target set by the manufacturer.
Hands-on: Make a simple model of induction on paper: draw a magnet spinning inside three coils and sketch the three AC waves they produce, each a third of a turn apart. Then, with an adult, look at the front of a car engine bay with the engine off and cold (look only) and spot the alternator, its pulley and the belt. Measure nothing and touch nothing; compare the pulley sizes by eye and estimate the ratio.
What you will learn
- I can describe the main parts of an alternator and what each one does.
- I can explain how the rectifier changes AC to DC and how the regulator controls the output voltage.
- I can calculate alternator speed from pulley sizes and output power from voltage and current.
- I can explain what the charge warning light means and describe common charging faults.
Key words
- alternator
- A machine driven by the engine that produces electricity to run the vehicle's loads and recharge the battery.
- rotor
- The spinning part of the alternator: an electromagnet fed with a small field current through brushes and slip rings.
- stator
- The fixed windings around the rotor in which the alternating current is produced, usually three-phase.
- rectifier
- A set of diodes that converts the alternator's AC output into DC.
- voltage regulator
- The circuit that controls the field current so the system voltage stays near a set value, typically about 14 V.
The big ideas
When the engine is running, the battery is not supposed to power the car. That job belongs to the charging system: an alternator driven by a belt from the engine, which supplies every electrical load and tops the battery back up after starting.
The alternator uses electromagnetic induction. A spinning magnet makes an alternating current in fixed coils. Diodes turn this into direct current, and a regulator keeps the voltage steady whatever the engine speed or the load.
The driver sees the charging system through one warning lamp. The Highway Code says warning lights should go out when the engine starts, and that if the charge warning light stays on while driving, the battery may not be charging. This lesson explains the theory; testing and repairing the charging system is work for a trained technician.
Read-through: the teaching steps
Induction: the basic idea
Moving a magnet near a coil of wire makes a voltage in the coil. The faster the magnet moves and the stronger it is, the bigger the voltage. If the magnet spins, the voltage keeps reversing: alternating current (AC).
An alternator spins an electromagnet (the rotor) inside fixed coils (the stator). Using an electromagnet rather than a permanent magnet means its strength can be controlled.
Inside the alternator
- Rotor – a coil wound inside claw-shaped iron poles. A small field current, a few amps, reaches it through carbon brushes running on slip rings.
- Stator – three sets of windings, giving three-phase AC that is smoother than a single phase.
- Rectifier – usually six diodes (three for the positive side, three for the negative) that turn the AC into DC.
- Regulator – controls the field current.
- Pulley and fan – driven by the auxiliary belt from the crankshaft; the fan cools the diodes and windings.
Rectification: AC to DC
A diode lets current flow in one direction only. Arranged as a bridge, the six diodes send each part of the three-phase AC wave the same way out of the alternator, so the output is DC with a small ripple.
The diodes also stop the battery from discharging back through the stator when the engine is off. A failed diode reduces output and can make a whining noise on the radio or let the battery drain.
Regulation
Without control, the output voltage would rise with engine speed and could boil the battery and damage electronics. The regulator watches the system voltage and switches the field current on and off very rapidly:
- voltage too low – more field current, stronger magnet, more output;
- voltage too high – less field current.
A typical regulated voltage is about 14 V. Many modern vehicles use "smart charging": the engine management varies the target voltage, charging harder when the car slows down and less when it accelerates, to save fuel. The vehicle maker's data gives the correct figures.
Pulley ratio and output
The alternator spins faster than the engine because its pulley is smaller than the crankshaft pulley.
- Pulley ratio = crankshaft pulley diameter ÷ alternator pulley diameter.
- Alternator speed = engine speed × pulley ratio.
Output power = system voltage × output current. An alternator rated at 120 A at about 14 V can supply about 1,680 W – but only at higher speeds. At idle the output is lower, which is why a heavy electrical load at idle can still draw on the battery.
The warning light and charging faults
The charge warning light is on with the ignition on and the engine stopped, and goes out once the alternator is charging. If it stays on, or comes on while driving, the Highway Code says the battery may not be charging.
Common causes, found by a technician using the manufacturer's information:
- a broken or slipping drive belt;
- worn brushes or a failed regulator;
- a failed diode;
- poor connections or a high-resistance earth.
Overcharging is a fault too: it can damage the battery and electronics. A broken belt may also drive other parts, so the vehicle should be stopped safely and checked by a qualified person.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Electrical and electronic systems lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- The Highway Code – Annex 6. Vehicle maintenance, safety and security
- US Department of Energy, Alternative Fuels Data Center – How do gasoline cars work?
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.