Lighting systems: bulbs, LEDs and headlamp aim – Motor Vehicle Theory motor mechanics lesson
Lesson 98 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out how filament, halogen, HID and LED lamps make light, what colours each vehicle lamp must be, and how headlamp aim is measured and checked in the MOT.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
The lesson covers lamp technology, colours and the MOT checks, with simple percentage calculations. The activity uses a torch at home; nothing is done to a real vehicle. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Adaptive LED headlamps can switch off parts of the beam to avoid dazzling others. What could go wrong with such a system, and how would a driver know?”
- Later: the homework, then the practice test.
Watch out for
- Thinking a brighter headlamp is always better. Light above the cut-off dazzles oncoming drivers. Correct aim and beam pattern matter as much as brightness.
- Thinking aim does not change once it is set. Load, suspension height and tyre pressures all tilt the beam. Levelling controls exist for this reason.
- Thinking an indicator flashing fast means the switch is faulty. A faster flash is a traditional warning that a bulb has failed, because the flasher circuit senses the lower current.
Hands-on: In a dark room, shine a torch at a wall from 2 m away, with the torch on a pile of books so it is level. Mark the height of the torch on the wall with tape, then tilt it slightly down and measure how far below the mark the brightest edge falls. Work out the percentage drop (drop in cm ÷ distance in m). Torch, books and tape measure only.
What you will learn
- I can explain how filament, halogen, HID and LED lamps produce light and compare their efficiency.
- I can state the required colours of the main vehicle lamps.
- I can explain dipped-beam aim as a percentage drop and convert it to a distance on a screen.
- I can describe what the MOT checks on lamps and indicators.
Key words
- halogen lamp
- A filament lamp filled with halogen gas, which lets the tungsten filament run hotter and brighter and last longer.
- LED
- Light-emitting diode: a semiconductor that gives out light when current flows through it in one direction. Far more efficient than a filament.
- HID (xenon) lamp
- High-intensity discharge lamp: light comes from an electric arc in xenon gas, started by a very high voltage.
- dipped beam
- The headlamp setting used when other road users are near. Its beam has a sharp cut-off that is aimed slightly down.
- beam aim
- The angle of the headlamp beam, often given as a percentage drop: 1% means 1 cm down for every metre in front of the lamp.
The big ideas
Lights let the driver see and let other road users see the vehicle and understand what it is about to do. GOV.UK tells drivers to check every time they drive that all lights work, and the Highway Code adds that lights, indicators, reflectors and number plates should be clean.
The technology has changed fast. Simple tungsten bulbs gave way to halogen lamps, then to high-intensity discharge (xenon) lamps, and now to LEDs, which use a fraction of the power and can be shaped into complex light signatures. Many new cars use matrix LED headlamps that switch segments off to avoid dazzling other drivers.
Whatever the light source, the rules care about three things: the lamp works, it is the right colour, and the headlamp beam is aimed correctly. This lesson explains how lamps work and how aim is measured; it is not a guide to adjusting or replacing lamps.
Read-through: the teaching steps
Filament and halogen lamps
A filament lamp passes current through a thin tungsten wire, heating it until it glows white. Most of the energy comes out as heat, not light.
A halogen lamp has a small quartz glass bulb filled with halogen gas. The gas returns evaporated tungsten to the filament, so it can run hotter and brighter without blackening the glass. Two practical points:
- skin oil on the quartz glass can create hot spots and shorten its life, which is why the glass is not touched;
- the bulb runs very hot, so lamps are only handled when cold.
A typical halogen headlamp bulb is about 55 W.
HID and LED lamps
HID (xenon) lamps make light from an arc between two electrodes in xenon gas. A ballast unit produces a very high starting voltage – thousands of volts – then a steady lower voltage. They are much brighter and more efficient than halogen. Because of the high voltage, they are handled only by trained technicians.
LEDs are semiconductors that emit light directly. They:
- use far less power for the same light;
- switch on instantly, which is why they are used for brake lamps;
- last a very long time but need heat sinks and driver electronics;
- are often built into a sealed unit, so a failure may mean replacing the whole lamp.
Lamp functions and colours
Each lamp has a job and a set colour. The DVSA MOT inspection manual lists:
- headlamps – white (or white with a blue tinge) or yellow;
- rear position and stop lamps – red;
- direction indicators – amber, flashing 60–120 times per minute;
- front fog lamps – white; rear fog lamp – red;
- reversing lamps – white;
- rear reflectors – red (reflective tape is not an acceptable substitute).
Daytime running lamps make the car easier to see in daylight but do not light the road.
Headlamp aim
A dipped beam has a sharp horizontal cut-off. Light below it lights the road; above it would dazzle oncoming drivers. The cut-off is aimed slightly down.
Aim is given as a percentage: a 1% drop means the beam falls 1 cm for every metre ahead, so 10 cm at 10 m. For European-style dipped beams with the lamp centre 850 mm or less above the ground, the MOT manual gives a cut-off between 0.5% and 2.75% below horizontal (1.25% to 2.75% for higher lamps).
Load changes aim: a heavy load in the boot tilts the nose up. Many cars have a manual levelling control or automatic levelling for this reason.
How aim is checked
In a workshop or MOT test centre, aim is checked with a beam-setting screen or optical aiming equipment, with the vehicle on level ground at the right tyre pressures and load. The tester sees where the cut-off falls and compares it with the limits.
In the MOT, a lamp that does not work, is the wrong colour or is aimed outside the limits is a defect. Adjusting aim is done by a trained person using the manufacturer's method.
Bulb monitoring
Many vehicles check their own lamps. A body control module measures the current each lamp draws. If a filament breaks, the current drops to zero and a warning appears; a faster flash rate on the indicators is a traditional sign of a failed bulb.
This is why fitting the wrong kind of bulb, or an LED where a filament is expected, can trigger false warnings – another reason lamp work follows the manufacturer's information.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Electrical and electronic systems lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- GOV.UK – Check your vehicle is safe to drive
- The Highway Code – Annex 6. Vehicle maintenance, safety and security
- DVSA MOT inspection manual: cars and passenger vehicles – 4. Lamps, reflectors and electrical equipment
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.