Cylinder block, crankshaft and bearings – Motor Vehicle Theory motor mechanics lesson
Lesson 21 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Learn how the cylinder block supports the crankshaft, how the crankshaft turns piston motion into rotation, and how plain bearings run on a film of oil.
- Time
- 40 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson explains the engine's bottom end using example figures. The activity is a cardboard model. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think engine designers balance the crankshaft so carefully?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the crankshaft rests on its bearings like a wheel on an axle. When running, it floats on a pressurised oil film; metal contact means damage.
- Thinking stroke equals the crank throw. The piston travels the throw down and back up: stroke = 2 × throw.
- Thinking more clearance always means better lubrication. Too much clearance lets oil pressure drop and the bearing knock.
Hands-on: Make a working cardboard model of a crankshaft: a cardboard disc on a pencil axle with a paper-fastener crankpin near the edge, and a card strip as the connecting rod joined to a 'piston' sliding in a cut-out slot. Measure the throw and the piston's travel and check that stroke = 2 × throw.
What you will learn
- I can describe the cylinder block and its features.
- I can name the parts of a crankshaft and explain their jobs.
- I can explain how plain bearings work and why oil clearance matters.
- I can relate crank throw to stroke and calculate mean piston speed.
- I can explain end float and the role of thrust bearings.
Key words
- cylinder block
- The main body of the engine, containing the cylinders and supporting the crankshaft.
- crankshaft
- The shaft that converts the pistons' up-and-down motion into rotation.
- main journal
- A part of the crankshaft that runs in a main bearing in the block.
- crankpin
- An offset journal that carries a connecting rod's big end.
- oil clearance
- The small gap between a bearing and its journal, filled by the oil film.
The big ideas
At the heart of every piston engine is the bottom end: the cylinder block, the crankshaft and its bearings. The block is the engine's backbone – it contains the cylinders, carries coolant and oil passages, and supports the crankshaft in its main bearings. The crankshaft turns the pistons' up-and-down movement, delivered by the connecting rods, into the rotation that the transmission carries to the wheels.
The crankshaft spins thousands of times a minute under huge loads, yet it does not touch its bearings: it runs on a thin film of pressurised oil. Clearances of a few hundredths of a millimetre make that possible.
This lesson explains how these parts work and why their measurements matter. The figures used are examples; real values come from the manufacturer's data, and engine work is done by trained technicians.
Read-through: the teaching steps
The cylinder block
Blocks are cast from iron (strong, hard-wearing) or aluminium (lighter). Aluminium blocks usually have cast-iron liners or hard coatings in the bores. The block contains water jackets for coolant, oil galleries feeding the bearings, and the main bearing housings, closed by bearing caps. See the cylinder and crankshaft in the drawing on the lesson page.
The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes. The crankshaft
- Main journals – run in the main bearings.
- Crankpins – offset journals carrying the connecting rods.
- Webs – join journals and crankpins.
- Counterweights – balance the rotating masses.
- Oil drillings – carry oil from the main journals to the crankpins.
The offset of the crankpin (the throw) sets the stroke: stroke = 2 × throw.
Plain bearings
Most car engines use plain bearings: thin steel shells lined with softer bearing material, fitted in halves. When the shaft turns, oil is dragged into the wedge-shaped gap and builds pressure, lifting the journal off the bearing – hydrodynamic lubrication. The soft lining can embed small dirt particles rather than scoring the journal.
Oil clearance
Clearance = bearing bore − journal diameter.
Too small and there is no room for the oil film; too large and oil escapes, pressure falls and the bearing knocks. Technicians measure journals with micrometers and compare with the manufacturer's data.
End float and thrust bearings
The crankshaft must not slide too far along its axis – for example when the clutch pedal is pressed. Thrust washers or flanged bearing shells control this. End float is measured with a dial gauge and compared with the specified range.
Piston speed
The piston stops and reverses twice every revolution. Its average speed is:
mean piston speed = 2 × stroke × rpm ÷ 60 (stroke in metres, answer in m/s).
High piston speeds increase wear and stress, which is one reason long-stroke engines rev less freely.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Marked by Classfern |
| Independent practice (three levels) | 11 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Engines lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.