▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

MOT: tyres and wheels – Motor Vehicle Theory motor mechanics lesson

Lesson 119 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

See how an MOT tester judges tyres and wheels: tread depth and where it is measured, cuts, bulges and exposed cords, tyre pressure monitoring and wheel condition.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson explains published MOT tyre standards (November 2026). It does not teach tyre fitting or inflation. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think the car tread rule ignores the outer quarters of the tyre?”
  4. Later: the homework, then the practice test.

Watch out for

  • Applying the 10-year tyre age rule to cars. In the MOT manual that rule is for vehicles with more than 8 passenger seats.
  • Thinking a TPMS lamp lit for low pressure is an MOT fail. That is the system working. Only a malfunctioning or not-working system is Major.

Hands-on: Draw a tyre tread across a strip of card, mark the central three-quarters, and shade grooves at different depths to show which would pass. With a qualified adult, look at the tyres of a parked, switched-off car (look only) and find the tread wear indicators and the four-digit date code.

What you will learn

  • I can state the car and motorcycle tread depth rules and where they apply.
  • I can describe how cuts, bulges and visible cords are categorised.
  • I can explain the MOT tyre pressure monitoring rule and its date.
  • I can explain why the 10-year tyre age rule does not apply to cars.

Key words

primary grooves
The main, wide grooves of the tread pattern, where tread depth is measured.
central three-quarters
The middle 75% of the tread width, where the car tread rule applies all the way round.
TPMS
Tyre pressure monitoring system: warns the driver when a tyre has lost pressure.
ply or cord
The strong fabric or steel layers inside a tyre. If they can be seen, the tyre fails.

The big ideas

Tyres are the vehicle's only contact with the road, so the MOT treats them seriously. Section 5.2 of the car inspection manual covers the road wheel and hub, road wheel condition and tyres. For cars (up to 8 passenger seats) first used on or after 3 January 1933, the primary grooves must be at least 1.6 mm deep within the central three-quarters of the breadth of the tread and around the entire circumference. The outer quarters may have no tread at all. Tread below the requirement is Dangerous.

Damage is judged carefully. Any ply or cord visible without touching fails the tyre. A cut longer than 25 mm or 10% of the section width (whichever is greater) and deep enough to reach the ply or cords is Major. A lump, bulge or tear caused by separation or partial failure of the tyre's structure is Dangerous. Testers are told to distinguish these from the normal small undulations of radial tyres.

Cars (M1) first used on or after 1 January 2012 have their tyre pressure monitoring system checked; a system that is malfunctioning or obviously not working is Major. A lamp lit only because a tyre is low is not a system fault. The 10-year tyre age rule in the manual applies to vehicles with more than 8 passenger seats, not cars. For motorcycles over 50 cc the tread must be at least 1.0 mm across a band of at least three-quarters of the breadth.

Read-through: the teaching steps

  1. Where tread is measured

    Car rule: at least 1.6 mm in the primary grooves, within the central three-quarters of the breadth, all the way round. The outer quarters can be smooth. See the drawing on the lesson page.

    Larger passenger vehicles (more than 8 passenger seats) and pre-1933 vehicles: 1.0 mm.

    Tread depthat least 1.6 mmCentral three-quarters of the treadTread blockGroove
    Tread depth is measured in the main grooves. For cars the legal minimum is 1.6 mm across the central three-quarters of the tread, all the way round.
  2. Cuts, bulges and cords

    • Ply or cord visible without touching: fail.
    • Cut over 25 mm or 10% of section width (whichever is greater) reaching the ply: Major.
    • Lump, bulge or tear from separation or partial structural failure: Dangerous.
    • Normal radial-ply undulations are not bulges.
  3. Reading the sidewall

    The sidewall carries the size, load and speed rating and a four-digit date code. The drawing on the lesson page labels these. The MOT age rule (10 years) applies only to vehicles with more than 8 passenger seats.

    205 / 55 R 16 91 VWidthin mmSidewall height% of widthRadialRim sizein inchesLoad indexSpeed rating
    Reading a tyre size code.
  4. Pressure monitoring

    M1 cars first used on or after 1 January 2012: TPMS checked. Malfunctioning or obviously not working = Major. A lamp on because a tyre is low is not a system fault – it is the system doing its job.

  5. Motorcycles and wheels

    Motorcycles over 50 cc: at least 1.0 mm across a band of at least three-quarters of the breadth, all the way round; up to 50 cc: visible tread pattern. Below = Dangerous.

    Wheels are checked for damage, distortion and security as part of section 5.2.

  6. Theory only

    This lesson explains the standards. Tyre fitting and inflation are workshop jobs for trained people: HSE warns about tyre explosions and multi-piece wheels.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More The MOT test lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.