▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

State inspection: tires and wheels – Motor Vehicle Theory motor mechanics lesson

Lesson 119 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

See how tires and wheels are judged in state inspections, with the tread rules New York and Pennsylvania publish and NHTSA's own advice on tread, age and pressure.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

This lesson explains published inspection and NHTSA guidance (November 2026). It does not teach tire mounting or inflation. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why might a tire be unsafe because of its age even when it has plenty of tread?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking every state uses the same tire rule. New York and Pennsylvania word their rules differently; always name the state.
  • Using the pressure printed on the tire's sidewall. That is the maximum. NHTSA says use the vehicle's Tire and Loading Information Label.

Hands-on: Draw a tire tread on card and mark which grooves would fail the Pennsylvania adjacent-treads rule. With a qualified adult, look at the tires of a parked, switched-off car (look only), try NHTSA's penny test and find the last four digits of the identification number.

What you will learn

  • I can explain that tire inspection rules are set by each state.
  • I can state New York's minimum tread and Pennsylvania's adjacent-groove rule.
  • I can describe NHTSA's 2/32-inch replacement advice and the penny test.
  • I can read a tire's age from the last four digits of its identification number.

Key words

primary grooves
The main, wide grooves of the tread pattern, where tread depth is measured.
2/32 of an inch
The tread depth NHTSA gives for replacing tires, and the minimum New York publishes. It is about 1.6 mm.
TPMS
Tire pressure monitoring system: warns the driver when a tire is significantly underinflated.
Tire Identification Number
The DOT code on the sidewall. Its last four digits give the week and year of manufacture.

The big ideas

Tire rules in inspections are set by each state. New York's inspection includes tires with a minimum tread of 2/32 of an inch. Pennsylvania rejects a tire if two adjacent treads have less than 2/32 of an inch remaining at any point. Virginia's checklist includes tires, wheels and rims.

NHTSA, the federal safety agency, gives the same 2/32-inch figure as the point to replace a tire. Its penny test: put a penny into a groove with Lincoln's head upside down; if you can see the top of his head, the tread is too shallow. NHTSA also says to check the pressure of all tires, including the spare, at least once a month when cold, using the vehicle's Tire and Loading Information Label rather than the number on the tire.

Age matters too. The last four digits of the DOT Tire Identification Number give the week and year of manufacture – 0308 means the 3rd week of 2008. NHTSA notes that some manufacturers recommend replacing tires 6 to 10 years old regardless of tread. TPMS has been required on passenger cars, light trucks and vans from model year 2008.

Read-through: the teaching steps

  1. Each state sets the rules

    • New York: minimum tread 2/32 in.
    • Pennsylvania: rejected if two adjacent treads have less than 2/32 in at any point.
    • Virginia: tires, wheels and rims are on the checklist.

    Always check the state's own page. See the drawing on the lesson page for how tread is measured in the grooves.

    Tread depthreplace at 2/32 inTread wear barTread blockGroove
    Tread depth is measured in the grooves. NHTSA says a tire should be replaced when the tread is worn down to 2/32 of an inch.
  2. Cuts, bulges and cords

    A bulge shows that the layers inside the tire have separated, so it can fail suddenly. Exposed cords mean the rubber has worn through. Inspectors in every state look for damage like this; technicians, not drivers, decide on repair or replacement.

  3. Reading the sidewall

    The last four digits of the DOT Tire Identification Number are week and year: 2319 = 23rd week of 2019. Some manufacturers recommend replacing tires 6–10 years old regardless of tread. The drawing on the lesson page labels the sidewall.

    205 / 55 R 16 91 VWidthin mmSidewall height% of widthRadialRim sizein inchesLoad indexSpeed rating
    Reading a tire size code.
  4. Pressure monitoring

    TPMS has been required on passenger cars, light trucks and vans from model year 2008. It warns only when a tire is significantly underinflated. A light that flashes for 60–90 seconds and then stays on means the system itself has a malfunction.

  5. Pressure, the driver's job

    NHTSA: check all tires including the spare at least once a month, cold (not driven for at least three hours), using the label on the driver's door edge or doorjamb. Proper inflation can save fuel and extend tire life. An adult does this with a gauge; inflation is not a job for a learner.

  6. Theory only

    This lesson explains the standards. Tire mounting and inflation are workshop jobs for trained people; OSHA has a specific standard for servicing rim wheels.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More State inspections lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.