▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Engine management: actuators and control loops – Motor Vehicle Theory motor mechanics lesson

Lesson 46 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out how the engine control unit turns decisions into action through injectors, coils, throttle motors and valves, and how feedback loops such as fuel trim keep the engine on target.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson explains engine management actuators and feedback control. Work on engine management systems is for trained technicians using the manufacturer's data. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “A car's long-term fuel trim has crept up to +20%. What kinds of fault would you think about, and why?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking closed-loop fuel control works all the time. It runs open loop when cold, at full throttle and during sudden changes. Closed loop needs a working oxygen sensor and steady conditions.
  • Thinking a positive fuel trim means the engine is running rich. A positive trim adds fuel, so the engine was lean before correction. Negative trim means it was rich.
  • Thinking PWM varies the supply voltage. The supply stays the same; the fraction of time it is switched on changes, which changes the average.

Hands-on: Be a closed-loop controller with a partner: one person holds a full jug of water and pours slowly into a glass with a line marked on it, while the other watches the level and says 'more', 'less' or 'hold'. Try it with the pourer's eyes closed (open loop) and open (closed loop) and compare how close you get to the line. Then calculate average voltage for a 12 V supply at duty cycles of 10%, 25%, 50% and 90%, and plot them. Do not connect anything to a real car for this activity.

What you will learn

  • I can name the main actuators an engine control unit drives and say what each does.
  • I can explain the difference between open-loop and closed-loop control.
  • I can describe how lambda feedback and fuel trims keep the mixture at its target.
  • I can calculate the average voltage of a pulse-width-modulated signal from its duty cycle.
  • I can apply a percentage fuel trim to a base injector pulse width.

Key words

actuator
A device the control unit drives to make something happen, such as an injector, ignition coil, throttle motor or valve.
open loop
Control without checking the result: the control unit sets an output from its maps and does not correct it from feedback.
closed loop
Control with feedback: the control unit measures the result and keeps correcting the output to reach a target.
fuel trim
A percentage correction the control unit adds to or takes from its base fuel quantity, based on oxygen sensor feedback.
pulse-width modulation (PWM)
Switching a supply on and off very quickly and varying the fraction of time it is on, to control an actuator's average power.

The big ideas

Sensors tell the engine control unit what is happening; actuators let it do something about it. The US Department of Energy describes the electronic control module as controlling the fuel mixture, ignition timing and emissions system. It does this by driving injectors, ignition coils, an electronic throttle, variable valve timing units, exhaust gas recirculation and purge valves, the fuel pump and the cooling fan.

Some of these outputs are set straight from stored maps (open loop). Others are corrected all the time using feedback (closed loop): the control unit measures the result, compares it with a target and adjusts. The clearest example is fuel control with an oxygen sensor, which keeps a petrol engine close to lambda 1 so the catalyst can work.

fueleconomy.gov lists variable valve timing and lift, one of these actuator-driven technologies, with a potential efficiency improvement of about 1% to 11%. This lesson explains the theory of actuators and control loops. It is not a repair guide: work on engine management systems is for trained technicians using the manufacturer's data.

Read-through: the teaching steps

  1. The main actuators

    The control unit's outputs include:

    • fuel injectors – how much fuel and when;
    • ignition coils – when each spark happens;
    • the electronic throttle – how much air enters;
    • variable valve timing units – when the valves open and close;
    • the EGR valve – how much exhaust gas is recirculated;
    • the purge valve – when fuel vapour from the charcoal canister is drawn into the engine;
    • the fuel pump, cooling fan, turbo wastegate or vanes, and glow plugs on a diesel.

    Most are switched electrically, either fully on and off or using pulse-width modulation.

  2. Pulse-width modulation

    Many actuators need a variable amount of power, but switching a transistor fully on or off wastes very little energy. So the control unit switches the supply on and off very quickly, perhaps hundreds of times a second, and varies the fraction of time it is on – the duty cycle.

    Average voltage ≈ supply voltage × duty cycle.

    At 12 V and a 40% duty cycle, an actuator sees an average of 0.40 × 12 = 4.8 V. A purge valve, a fan controller or an idle valve can be held part-open in this way.

  3. Open loop and closed loop

    In open loop, the control unit takes its output from a stored map and does not check the result. Fuel control is open loop when the engine is cold (the oxygen sensor is not yet working), at full throttle (when it deliberately runs slightly rich) and during sudden changes.

    In closed loop, it measures the result and corrects the output:

    measure → compare with target → adjust → measure again.

    Once warm and cruising, a petrol engine's fuel control is closed loop, using the oxygen sensor to hold the mixture near lambda 1. Idle speed control is another closed loop: the control unit adjusts the throttle and timing to hold its target idle speed.

  4. Fuel trims

    In closed loop, the oxygen sensor shows whether the mixture is rich or lean. The control unit responds with a fuel trim, a percentage correction to its base fuel:

    • Short-term fuel trim changes quickly, moment by moment.
    • Long-term fuel trim learns a lasting correction over time, so the short-term trim can stay near zero.

    A positive trim adds fuel (the engine was running lean); a negative trim removes fuel (it was running rich). A large long-term trim tells a technician something is wrong, for example an air leak after the air flow sensor, which makes the engine run lean and the trim go positive.

  5. Electronic throttle and valve timing

    With an electronic throttle, the control unit reads the accelerator pedal sensors and drives a small motor to open the throttle plate, checking its position with throttle position sensors – another closed loop. This lets it smooth gear changes, control idle and limit power when needed.

    Variable valve timing units, usually oil-pressure-operated phasers on the camshafts switched by solenoid valves, shift the camshaft timing to suit speed and load. The control unit checks the actual timing with the camshaft sensors and corrects it.

  6. Monitoring and fail-safe

    The control unit checks its actuators as well as its sensors. It can see whether an injector circuit draws the expected current, or whether the throttle reached the position it was told. If something is wrong, it stores a fault code, may light the engine warning lamp, and uses a fail-safe strategy – for example limiting power (limp mode) or running a fan constantly.

    This self-checking is why a technician's first step is usually to read the fault codes and live data, but the codes are evidence to test, not the final answer.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Fuel, ignition and emissions lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.