▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Engine management: sensors – Motor Vehicle Theory motor mechanics lesson

Lesson 45 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Meet the sensors that tell the engine control unit what is happening – crankshaft and camshaft position, air flow and pressure, temperatures, pedal position, oxygen and knock – and learn how their signals become numbers.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson explains how engine management sensors work. Testing sensors on a running engine involves moving parts and hot surfaces and is for trained technicians using the manufacturer's data. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think the accelerator pedal has two separate sensors inside it, when one would be enough to measure its position?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a fault code always means the named sensor is broken. A code can come from the sensor, its wiring or connector, or a real engine problem the sensor is correctly reporting. Technicians test before replacing.
  • Thinking the MAP sensor reading is high at idle. With the throttle nearly closed the engine sucks the manifold to a low absolute pressure. Pressure rises towards atmospheric as the throttle opens.
  • Thinking the control unit needs only the crankshaft sensor to know which stroke each cylinder is on. The crankshaft turns twice per cycle, so the camshaft sensor is used to tell compression from exhaust.

Hands-on: Make a potential divider table on paper: with a 5 V reference and a 2 kΩ fixed resistor, calculate the sensor voltage for sensor resistances of 5,000, 2,000, 1,000, 500 and 200 Ω, and plot voltage against resistance. Then make a model trigger wheel: cut a card circle with 12 notches and leave out one, spin it slowly past a pencil 'sensor' and count the clicks, noticing the gap that marks the reference point. Do not connect anything to a real car for this activity.

What you will learn

  • I can explain why the engine control unit needs sensors and name the main ones.
  • I can describe how crankshaft and camshaft position sensors let the control unit find engine speed and position.
  • I can compare measuring engine load with a mass air flow sensor and with a manifold pressure sensor.
  • I can calculate a sensor voltage from a potential divider.
  • I can calculate engine speed from the frequency of a crankshaft sensor signal.

Key words

engine control unit (ECU)
The computer that reads the sensors and controls fuel, ignition and emissions. The US Department of Energy calls it the electronic control module.
crankshaft position sensor
A sensor that reads a toothed wheel on the crankshaft to give engine speed and the position of the pistons.
mass air flow (MAF) sensor
A sensor in the air intake that measures the mass of air entering the engine each second.
MAP sensor
A manifold absolute pressure sensor, which measures the pressure in the inlet manifold. Low pressure means light load.
reference voltage
A steady supply, usually 5 V, that the control unit gives to many sensors so it can read their output accurately.

The big ideas

The US Department of Energy describes the electronic control module as the part that controls the fuel mixture, ignition timing and emissions system, and that monitors the operation of the vehicle, protects the engine from abuse, and detects and troubleshoots problems. To do any of that, it needs information: how fast the engine is turning and where each piston is, how much air is coming in, how hot things are, what the driver wants, and how clean the combustion is.

That information comes from sensors. Each one turns a physical quantity – position, pressure, temperature, flow, oxygen, vibration – into an electrical signal: a changing voltage, a changing frequency, or a digital message. The control unit reads these hundreds of times a second and also checks them against each other, so it can spot a sensor giving nonsense and store a fault code.

This lesson explains how the main sensors work. It is not a repair guide: testing sensors on a running engine is for trained technicians, using the manufacturer's data.

Read-through: the teaching steps

  1. Inputs, processing, outputs

    Engine management works like any control system:

    • Inputs: the sensors measure what is happening.
    • Processing: the control unit compares the readings with maps and targets stored in its memory.
    • Outputs: it drives actuators such as injectors, ignition coils, the throttle and valves.

    This lesson is about the inputs. The next lesson looks at the outputs and how the control loops work.

  2. Crankshaft and camshaft position

    The most important sensor is the crankshaft position sensor. It faces a toothed wheel on the crankshaft – often a 60-tooth pattern with two teeth missing, so the control unit can find a reference point. Each passing tooth makes a pulse; the gap shows where the crankshaft is.

    • Inductive sensors make an alternating voltage that grows with speed.
    • Hall-effect sensors give a clean on–off square wave at any speed.

    The crankshaft turns twice per four-stroke cycle, so a camshaft position sensor is also used to tell compression from exhaust stroke. Without a crankshaft signal, most engines will not run at all.

  3. Measuring the air

    To add the right fuel, the control unit must know how much air is entering. Two methods are used, sometimes together:

    • A mass air flow sensor sits in the intake. A heated film or wire is cooled by the passing air; the current needed to keep it hot shows the mass of air flowing.
    • A manifold absolute pressure (MAP) sensor measures the pressure in the inlet manifold. With engine speed and air temperature, the control unit calculates the air entering. At idle with the throttle nearly shut the manifold pressure is low; at full throttle it is close to atmospheric (or above it on a turbo engine).

    An intake air temperature sensor helps, because cold air is denser.

  4. Temperature sensors and the potential divider

    Coolant and intake air temperature sensors are usually NTC thermistors: resistance falls as temperature rises. The control unit feeds a 5 V reference through a fixed resistor in series with the sensor and measures the voltage across the sensor:

    V_out = V_ref × R_sensor ÷ (R_fixed + R_sensor).

    With a 2.5 kΩ fixed resistor and a cold sensor of 2.5 kΩ, V_out = 5 × 2.5 ÷ 5.0 = 2.5 V. When hot, the sensor might fall to 300 Ω, giving 5 × 0.3 ÷ 2.8 = 0.54 V. So a falling voltage means a warmer engine.

  5. What the driver wants

    Most modern cars have no cable from the accelerator pedal to the engine. An accelerator pedal position sensor – usually two separate sensors in one unit, for safety – reports how far the pedal is pressed. The control unit then opens an electronic throttle, checked by its own throttle position sensors.

    If the two pedal signals disagree, the control unit knows one has failed and limits power (limp mode). Other driver inputs include the brake pedal switch, which also cuts the throttle request if both pedals are pressed.

  6. Oxygen and knock sensors

    Two sensors report on the combustion itself:

    • Oxygen (lambda) sensors in the exhaust show whether the mixture is rich or lean. A sensor before the catalyst is used to control the fuel; one after it checks that the catalyst is working.
    • Knock sensors are piezoelectric: they produce a small voltage when squeezed by vibration. They pick up the sharp vibration of knock so the control unit can retard the timing.

    The control unit also checks the sensors for plausibility – for example, a coolant temperature that never rises – and stores a fault code if something does not make sense.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Fuel, ignition and emissions lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.