Lead-acid batteries: construction, ratings and testing – Motor Vehicle Theory motor mechanics lesson
Lesson 95 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out what is inside a 12 V lead-acid battery, what its ratings mean, how its state of charge is judged, and why batteries are treated as a workshop hazard.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson covers battery chemistry, ratings and simple capacity calculations. Batteries hold acid and can produce explosive gas, so the activity is look-only and any practical work belongs in a supervised college workshop. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Electric cars carry a large high-voltage battery, yet most still have a small 12 V battery as well. Why do you think that is?”
- Later: the homework, then the practice test.
Watch out for
- Thinking a 12 V battery is "flat" only when it reads 0 V. A resting voltage of about 12.0 V already means the battery is close to flat. Small voltage differences mean big differences in charge.
- Thinking a good resting voltage proves the battery is healthy. A worn battery may show a normal voltage but collapse under the heavy current of starting. That is why load or conductance testing is used.
- Thinking batteries give off no gas because they are sealed. Charging can still produce hydrogen, and sealed batteries have vents. Sparks and flames are kept away from all batteries.
Hands-on: With an adult, look at the label on a car battery without touching it (or find a battery label picture in a handbook). Note the voltage, the Ah capacity and the cold cranking figure. Then work out how long it could run a 5 W number plate lamp (I = P ÷ V) before reaching half charge. Look only: do not touch the terminals, move the battery or connect anything.
What you will learn
- I can describe the construction of a lead-acid battery and the chemistry of charge and discharge.
- I can explain amp-hour capacity, cold cranking current and reserve capacity.
- I can relate resting voltage to state of charge and calculate how long a load will take to flatten a battery.
- I can explain the hazards of batteries and why battery testing is done by trained people.
Key words
- cell
- One unit of the battery, giving about 2.1 V when fully charged. A 12 V battery has six cells in series.
- electrolyte
- The liquid (or gel or soaked mat) between the plates: dilute sulphuric acid.
- amp-hour (Ah)
- A measure of capacity: the current a battery can supply multiplied by the time, usually measured over 20 hours.
- cold cranking amps (CCA)
- The large current a battery can deliver for a short time at low temperature while keeping its voltage up – a measure of starting ability.
- parasitic drain
- The small current drawn by clocks, alarms and control units while the vehicle is parked.
The big ideas
The battery has two jobs. The US Department of Energy's guide to petrol cars sums them up: it starts the engine and powers the electronics. It must deliver a very large current for a few seconds to turn the starter motor, and a small current for weeks to keep alarms and memories alive while the car is parked.
Most vehicles still use a 12 V lead-acid battery for this low-voltage system, even electric cars, which have one alongside their high-voltage traction pack. It stores energy chemically: charging turns electrical energy into chemical energy, and discharging turns it back.
Batteries are also a hazard. HSE lists battery gases, acid and short circuits among the risks in motor vehicle repair. Checking and testing batteries is done in a workshop by trained people with eye protection; this lesson explains the theory only.
Read-through: the teaching steps
Inside the battery
A 12 V battery contains six cells in series, each giving about 2.1 V when fully charged: 6 × 2.1 = 12.6 V.
Each cell has:
- positive plates of lead dioxide;
- negative plates of spongy lead;
- porous separators to stop the plates touching;
- electrolyte of dilute sulphuric acid.
The plates are grids packed with active material, and many plates are used in each cell to give a large surface area – that is what lets the battery deliver a big current.
Charge and discharge
During discharge, both plates slowly turn into lead sulphate and the acid becomes weaker, more like water. During charging the process reverses.
- The strength of the acid is shown by its relative density (specific gravity): typically about 1.28 when fully charged and much lower when flat.
- A battery left flat for a long time grows hard sulphate crystals that will not convert back – sulphation – and loses capacity.
- Near the end of charging, water in the electrolyte splits into hydrogen and oxygen. Hydrogen is explosive, which is why sparks and flames are kept well away from batteries.
Types of lead-acid battery
There are several designs:
- Flooded (wet) batteries – liquid electrolyte; most are now sealed "maintenance-free" types.
- EFB (enhanced flooded) – stronger plates for stop-start vehicles that restart the engine many times.
- AGM (absorbent glass mat) – the acid is soaked into glass-fibre mats; they handle deep cycling and stop-start well.
Vehicles designed for AGM or EFB batteries need the same type as a replacement, and on many cars the battery management system must be told a new battery has been fitted.
Ratings
Battery labels show several ratings:
- Capacity in amp-hours (Ah), usually at the 20-hour rate: a 60 Ah battery can supply about 3 A for 20 hours.
- Cold cranking current – the current it can deliver at low temperature for a short time while keeping its voltage up. This is what starts the engine on a cold morning. Different standards (for example SAE in the US and EN in Europe) measure it slightly differently, so figures from different standards are not directly compared.
- Reserve capacity – how many minutes the battery can supply a steady load if the charging system fails.
The right battery for a vehicle is the one the manufacturer specifies.
Judging state of charge
A technician judges a battery in several ways, using the manufacturer's and the tester's instructions:
- Resting (open-circuit) voltage after the battery has stood with no load: typically about 12.6–12.7 V when fully charged, about 12.2 V at half charge and about 12.0 V or less when flat.
- Electronic conductance testers, which estimate the battery's condition from its internal resistance.
- Load testing, which checks that the voltage holds up while a heavy current is drawn.
A battery can show a good resting voltage but still fail under load, which is why more than one test is used.
Hazards and the law
HSE lists battery hazards in motor vehicle repair: explosive gases, corrosive acid and short circuits, which can make tools red hot. A battery is also heavy, so lifting it is a manual handling task.
In the MOT the battery is checked for security and leaks: insecure but unlikely to fall is minor; likely to fall, cause a short circuit, or leaking is major. Used lead-acid batteries are hazardous waste (waste code 16 06 01*) and must go for proper recycling.
Battery work is done only by, or with, a qualified person, wearing eye protection. Never touch the high-voltage battery of an electric or hybrid vehicle: HSE says that is for trained technicians only.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Electrical and electronic systems lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- US Department of Energy, Alternative Fuels Data Center – How do gasoline cars work?
- HSE – Introduction to safe motor vehicle repair
- HSE – Electric and hybrid vehicles
- GOV.UK / Environment Agency – Vehicle and oily wastes: how to classify
- HSE – Manual handling at work
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.