▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Brake fluid: types, boiling point and contamination – Motor Vehicle Theory motor mechanics lesson

Lesson 68 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out why brake fluid must have a high boiling point, how the DOT grades differ, why fluid absorbs water and ages, and how fluid condition is checked.

Time
40 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson explains brake fluid properties using the US federal standard FMVSS 116 (values as of November 2026). Brake fluid is harmful; learners must not handle it, and all brake work is for trained technicians. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think the standard gives a "wet" boiling point as well as a "dry" one? Which is more useful to a driver?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking brake fluid lasts for ever. Glycol fluid absorbs water and its boiling point falls, so makers set a change interval.
  • Thinking DOT 5 is simply a "better" DOT 4. DOT 5 is silicone-based and must not be mixed with glycol-based fluids.
  • Forgetting the +32 when converting °C to °F. °F = °C × 9 ÷ 5 + 32.

Hands-on: Make a fact card for each DOT grade showing its base, colour and dry and wet boiling points from FMVSS 116, in °C and °F. Then, with an adult, watch what happens to a few drops of water on a saucer of salt left in a damp room for a day: the salt absorbs water, like a hygroscopic fluid. Never open, touch or taste real brake fluid.

What you will learn

  • I can explain why a high boiling point matters and what vapour lock is.
  • I can compare DOT 3, DOT 4, DOT 5 and DOT 5.1 fluids using the federal standard.
  • I can explain why glycol fluids absorb water and what that does to the boiling point.
  • I can calculate boiling point changes and convert between °C and °F.

Key words

equilibrium reflux boiling point (ERBP)
The standard laboratory measure of a brake fluid's boiling point.
wet boiling point
The boiling point after the fluid has absorbed a set amount of water in a standard test.
hygroscopic
Able to absorb water from the air.
vapour lock
Brake failure caused by fluid boiling and forming compressible vapour bubbles.
DOT grade
The grade of brake fluid set by the US federal standard FMVSS 116 (DOT 3, DOT 4, DOT 5).

The big ideas

This is explanation for understanding, not a repair guide. Brake fluid is harmful to skin and eyes and damages paint, and brake systems are safety-critical, so only trained technicians handle it.

Brake fluid carries the pressure from the pedal to every wheel. It must stay liquid over a huge temperature range, must not attack the rubber seals and, above all, must not boil when the brakes are hot. The DOT grades printed on fluid containers come from the US federal standard FMVSS 116, whose purpose is to reduce failures in hydraulic braking systems caused by improper or contaminated fluid.

Most fluids slowly absorb water from the air, which lowers their boiling point. That is why fluid condition is checked at services and the MOT inspection manual (section 1, as of November 2026) treats clearly contaminated fluid as a Major defect.

Read-through: the teaching steps

  1. Why boiling matters

    Braking heat flows from the pads into the caliper pistons and the fluid behind them. If the fluid boils, bubbles of vapour form. Vapour compresses, so pressing the pedal squashes the bubbles instead of applying the brakes, and the pedal may sink to the floor. This is vapour lock. It is most likely after long or repeated hard braking, for example down a mountain road.

  2. The DOT grades

    FMVSS 116 sets minimum boiling points (as of November 2026):

    • DOT 3: dry ERBP 205 °C; wet 140 °C.
    • DOT 4: dry 230 °C; wet 155 °C.
    • DOT 5: dry 260 °C; wet 180 °C.

    DOT 3, DOT 4 and DOT 5.1 are glycol-based ("non-silicone"). DOT 5 is silicone-based. The vehicle handbook says which grade to use.

  3. Colours and labels

    The standard sets colours so fluids are not confused:

    • DOT 3, DOT 4, DOT 5.1 non-silicone: colourless to amber.
    • DOT 5 silicone base: purple.
    • Hydraulic system mineral oil (used in some systems): green.

    Containers must carry warnings including "KEEP BRAKE FLUID CLEAN AND DRY" and an instruction to keep the container tightly closed to prevent absorption of moisture.

  4. Water and ageing

    Glycol fluids are hygroscopic: they take up moisture through hoses, seals and the reservoir vent. Water lowers the boiling point; the "wet" figures show how far it can fall. Water can also cause internal corrosion. Manufacturers therefore set a fluid change interval in the service schedule. Silicone DOT 5 absorbs little water but has a different base, so it must not be mixed with glycol fluids.

  5. Checks and disposal

    The MOT inspection manual (section 1, as of November 2026): fluid level is checked only in transparent reservoirs, without removing caps. Below the minimum mark is Minor; significantly below is Major; not visible is Dangerous. Clearly contaminated fluid is Major. A low level may mean worn pads or a leak.

    GOV.UK vehicle waste guidance lists brake fluid as hazardous waste (16 01 13*). It must not be mixed with oils or antifreeze.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Brakes lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.