▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Brake efficiency and brake testing – Motor Vehicle Theory motor mechanics lesson

Lesson 72 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Learn how brake efficiency and imbalance are calculated, how the MOT tests brakes with roller testers, plate testers and decelerometers, and the efficiency figures a car must reach.

Time
50 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson covers brake efficiency and testing. Rules quoted are dated November 2026 and come from official sources; check the official source before relying on them. Brake testing is done only by trained testers and technicians. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “The MOT allows newer cars a higher efficiency requirement than older ones. Why do you think the rule changed for cars first used from September 2010?”
  4. Later: the homework, then the practice test.

Watch out for

  • Using mass instead of weight. Weight in newtons = mass in kg × 9.81.
  • Dividing by the lower effort when finding imbalance. Divide by the higher effort.
  • Mixing up the 58%, 50%, 25% and 16% figures. 58% and 50% are service brake figures (newer and older M1 cars); 25% is the secondary brake; 16% is the parking brake.

Hands-on: Make a results sheet for an imaginary roller brake test: choose four wheel forces and a car mass, then calculate efficiency and front and rear imbalance, and decide the MOT category using the figures in this lesson. Swap sheets with a partner and check each other's working. If you visit a garage, watch any brake testing only with a qualified adult, from where the staff say is safe.

What you will learn

  • I can calculate brake efficiency from braking force and weight, and from deceleration.
  • I can calculate brake imbalance and explain why it matters.
  • I can describe the roller, plate and decelerometer tests used in the MOT.
  • I can state the MOT service, secondary and parking brake efficiency requirements and their defect categories.

Key words

brake efficiency
Total braking force ÷ vehicle weight × 100, or deceleration ÷ 9.81 × 100.
imbalance
The difference in braking between two wheels on one axle: (higher − lower) ÷ higher × 100.
roller brake tester
A machine with rollers that turn each wheel and measure the braking force it makes.
Dangerous defect
An MOT defect that is a direct and immediate risk to road safety; the vehicle should not be driven until repaired.

The big ideas

This is explanation for understanding, not a repair guide. Brakes are safety-critical, and brake tests are carried out only by trained testers and technicians.

A brake test measures how much braking force each wheel produces and compares the total with the vehicle's weight. This gives the brake efficiency, a percentage that lets cars of any weight be compared. Comparing the two wheels on each axle gives the imbalance, which shows whether the car would pull to one side.

In the MOT, the DVSA inspection manual (section 1, as of November 2026) sets the tests and limits: a roller brake tester is the primary test; cars (M1) first used on or after 1 September 2010 must reach 58% service brake efficiency, earlier ones 50%, and the parking brake 16%.

Read-through: the teaching steps

  1. Brake efficiency

    Efficiency = total braking force ÷ vehicle weight × 100.

    Weight = mass × 9.81 (in newtons). A road test gives the same idea from deceleration: efficiency ≈ deceleration ÷ 9.81 × 100, because a braking force equal to the full weight would give a deceleration of 1 g (9.81 m/s²).

  2. Imbalance

    Imbalance = (higher effort − lower effort) ÷ higher effort × 100.

    Unequal braking across an axle creates a turning moment, so the vehicle pulls towards the stronger side. On the steered front axle this is especially dangerous.

  3. MOT test methods

    The MOT inspection manual (section 1, as of November 2026):

    • Roller brake tester: the primary test. Rollers turn each wheel and measure its braking force.
    • Plate brake tester: the car is driven onto plates at about 4 mph and brakes; the system calculates efficiency and imbalance.
    • Decelerometer: used where the car cannot be tested on rollers; a road test at about 20 mph (32 km/h) on a level road.

    If more than half the wheels of a system lock on test, its efficiency requirement is considered met.

  4. MOT efficiency requirements

    Section 1.2.2 and 1.4.2 (as of November 2026):

    • Service brake, M1 first used on or after 1 September 2010: 58%.
    • Service brake, M1 first used before that date: 50%.
    • Secondary brake ("all other vehicles"): 25%.
    • Parking brake ("all other vehicles"): 16%.

    Below the requirement = Major; less than 50% of the required value = Dangerous.

  5. Imbalance limits in the MOT

    Section 1.2.1 (as of November 2026): on the same axle, a wheel's effort below 70% of the other wheel's maximum = Major; on a steered axle, below 50% = Dangerous. Imbalance is ignored where the lower effort comes from a locked wheel, or where the higher effort is not more than 40 kg.

  6. Safety around testing

    Roller testers turn wheels with powerful motors, and road tests involve hard braking. Only trained testers, inspectors and technicians carry them out, in safe places. Learners watch only, from a safe position, with a qualified adult.

The lesson, step by step

50 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task15 minNot assessed, self-checked
Worked examples and guided practice10 minMarked by Classfern
Independent practice (three levels)16 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Brakes lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.