▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Compression ratio: a simple calculation – Garage Basics motor mechanics lesson

Lesson 5 of 70 in the Garage Basics course (ages 11–16)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out what compression ratio means, calculate it from the swept and clearance volumes, and see why diesel engines squeeze their air much harder than petrol engines.

Time
45 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

Use a needle-free plastic syringe, the kind given with children's medicine, filled only with air. Every answer is marked straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think a diesel engine can be harder to start on a very cold morning?”
  4. Later: the homework, then the practice test.

Watch out for

  • Dividing the swept volume by the clearance volume. Add the clearance volume to the swept volume first: CR = (swept + clearance) ÷ clearance.
  • Thinking a higher ratio is always better. In a petrol engine, too high a ratio causes knock. Each fuel and engine has a sensible range.

Hands-on: Pull the plunger of a large plastic syringe (no needle) out to the 50 ml mark, put your finger over the end, and push the plunger in to the 10 ml mark. The air has been squeezed to one fifth of its volume: a compression ratio of 5:1. Feel how much harder it gets to push as the space gets smaller. Then let go slowly. Use only air.

What your child will learn

  • I can explain what swept volume and clearance volume are.
  • I can calculate a compression ratio.
  • I can rearrange the formula to find the clearance volume.
  • I can explain why diesel engines need a higher compression ratio than petrol engines.

Key words

compression ratio
How many times the gas in a cylinder is squeezed: total volume at the bottom of the stroke divided by the volume left at the top.
swept volume
The volume the piston moves through in one stroke.
clearance volume
The small space left above the piston at top dead centre. It is also called the combustion chamber volume.
knock
A sharp metallic noise caused when the mixture in a petrol engine explodes too early, by itself, instead of burning smoothly from the spark.
compression ignition
Igniting fuel using only the heat of strongly compressed air, as in a diesel engine.

The big ideas

On the compression stroke, the piston squeezes the gas in the cylinder into a much smaller space. The compression ratio tells us how many times smaller.

When the piston is at the bottom, the cylinder holds the swept volume plus the small clearance volume above the piston at the top. When the piston is at the top, only the clearance volume is left. So:

Compression ratio = (swept volume + clearance volume) ÷ clearance volume.

Squeezing a gas raises its temperature and pressure. A higher compression ratio generally lets an engine get more work from each drop of fuel. Petrol engines are limited because the mixture can ignite by itself (knock) if it gets too hot; typical petrol engines have ratios of about 10:1. A diesel engine squeezes only air, then injects fuel, which the US Department of Energy explains is ignited by the high temperature reached during compression. Diesels typically use ratios of about 15:1 to 20:1.

Read-through: the teaching steps

  1. Two volumes

    At bottom dead centre the space in the cylinder is the swept volume plus the clearance volume. At top dead centre the piston has risen, and only the clearance volume is left. Compare the piston positions in the drawing on the lesson page.

    1 Intake2 Compression3 Power4 Exhaustinout
    The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes.
  2. The formula

    Compression ratio (CR) = (swept volume + clearance volume) ÷ clearance volume.

    It is written as a ratio like 10:1, read "ten to one". It means the gas is squeezed into a space one tenth of its starting volume.

  3. A worked check

    A cylinder has a swept volume of 450 cc and a clearance volume of 50 cc.

    • Total at the bottom = 450 + 50 = 500 cc
    • Volume at the top = 50 cc
    • CR = 500 ÷ 50 = 10, so 10:1
  4. Finding the clearance volume

    If you know the CR and the swept volume, rearrange:

    Clearance volume = swept volume ÷ (CR − 1).

    For a 500 cc cylinder with a CR of 11:1, clearance = 500 ÷ 10 = 50 cc.

  5. Why squeeze harder?

    Squeezing gas heats it. In a petrol engine, too much heat makes the mixture ignite on its own before the spark – this is knock, and it can damage an engine. So petrol engines use moderate ratios. A diesel squeezes only air, so there is nothing to ignite early. It needs high compression to make the air hot enough to ignite the fuel the moment it is injected.

  6. Typical values

    • Typical petrol car engine: about 9:1 to 12:1
    • Typical diesel car engine: about 15:1 to 20:1

    The exact figure for any engine is given in the maker's data.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Engines and fuel lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.