Anti-lock brakes (ABS): the idea – Garage Basics motor mechanics lesson
Lesson 29 of 70 in the Garage Basics course (ages 11–16)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out why a locked, skidding wheel is a problem, how anti-lock brakes sense it and release the pressure many times a second, and what ABS can and cannot do.
- Time
- 40 minutes + 10 min homework
- Course
- Garage Basics (ages 11–16)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.
For parents: how to use this lesson
The toy car activity shows how a locked wheel slides. No real vehicle is involved; brakes and ABS are safety-critical and are worked on only by qualified technicians. Every answer is marked straight away with a worked explanation.
- Read what your child will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think it matters so much that a driver can still steer while braking hard?”
- Later: the homework, then the practice test.
Watch out for
- Thinking ABS always makes a car stop in a shorter distance. Its main job is to keep steering control. On some surfaces, such as loose gravel or snow, stopping can even take a little longer.
- Thinking a pulsing brake pedal means the brakes are broken. Pulsing during hard braking is ABS working normally.
- Thinking ABS gives grip on ice. ABS can only use the grip that is there. On ice, grip is very low with or without ABS.
Hands-on: Slide a toy car with rubber tyres across a smooth table in two ways: once rolling freely, and once with a strip of sticky tape wrapped round its wheels so they cannot turn. Give it the same gentle push each time. Then try to steer each one by pushing gently on the side of the front as it moves. Which one keeps going in a straight line whatever you do?
What your child will learn
- I can explain why a locked wheel loses steering and usually grip.
- I can name the parts of an ABS system and say what each does.
- I can calculate wheel slip as a percentage.
- I can explain what ABS does and does not do for stopping distance.
Key words
- ABS
- Anti-lock braking system: it stops the wheels locking under hard braking.
- wheel speed sensor
- A sensor at each wheel that measures how fast the wheel is turning.
- modulator
- The ABS unit with valves and a pump that can lower, hold and raise the brake pressure to each wheel.
- wheel slip
- How much slower a braked wheel turns than it would if it were rolling freely, as a percentage. A locked wheel has 100% slip.
- ECU
- Electronic control unit: the small computer that reads the sensors and controls the modulator.
The big ideas
If a driver brakes too hard, a wheel can stop turning while the car is still moving. The tyre then slides over the road. A sliding tyre usually grips less than one that is still rolling at the edge of grip, and, worse, a locked front wheel cannot steer the car. The Highway Code warns that locked wheels can lead to loss of control.
Anti-lock brakes (ABS) prevent this. A sensor at each wheel tells an electronic control unit how fast that wheel is turning. If one wheel slows much faster than the car could possibly slow, the unit knows it is about to lock. Valves in the ABS modulator then reduce the brake pressure to that wheel for a moment, let it speed up, and apply the pressure again. This happens many times a second, so the driver feels the pedal pulse.
ABS keeps the wheels turning so the driver can still steer while braking hard. It does not always shorten the stopping distance: the Highway Code (rule 120) says drivers should not assume a vehicle with ABS will stop in a shorter distance.
Read-through: the teaching steps
Why locked wheels are bad
A rolling tyre grips the road where it touches. A locked tyre slides. Sliding friction is usually lower than the best rolling grip, so the car slows less. And a sliding front tyre cannot change the car's direction, so turning the steering wheel does nothing.
Wheel speed sensors
Each wheel has a toothed ring (or magnetic ring) that turns with it and a sensor that counts the teeth going past. The faster the wheel turns, the more pulses per second. The same sensors are used by other systems, such as traction control and the speedometer.
The control unit decides
The ECU compares the wheel speeds with each other and with how fast the car is slowing. A wheel that suddenly slows much faster than the others is about to lock. The ECU acts within a few thousandths of a second.
Release, hold, reapply
The modulator has valves for each wheel. To stop a wheel locking it:
- holds the pressure steady,
- lowers it so the wheel speeds up again,
- then raises it again.
This cycle repeats many times a second. The driver feels it as a rapid pulsing in the pedal, which is normal.
Wheel slip
Wheel slip (%) = (car speed − wheel speed) ÷ car speed × 100, with the wheel speed measured at the tyre's edge. A freely rolling wheel has 0% slip; a locked wheel has 100%. Most tyres grip best at a small amount of slip, often around 10–20%, and ABS works to keep the wheels near this range.
What ABS does not do
ABS cannot add grip that the tyres and road do not have. On ice the car still needs a very long distance to stop. The Highway Code says drivers with ABS should follow the advice in the vehicle handbook. At the MOT the ABS warning light is checked; a light showing a fault is a reason for failure.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Marked by Classfern |
| Independent practice (three levels) | 11 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Brakes, steering and suspension lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- DVSA MOT inspection manual: cars and passenger vehicles – 1. Brakes
- The Highway Code – Rules 103 to 158: general rules for all drivers and riders
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.