▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Altimeter setting rules: QNH, QFE and 1013.2 hPa (UK) vs 29.92 inHg and 18,000 ft (US) – Private Pilot Theory aviation lesson

Lesson 15 of 228 in the Private Pilot Theory course (ages 16+)

UK version. UK spelling and units (hPa, metres, litres) and the UK CAA. · US version

An altimeter only reads correctly if it is set to the right pressure. Learn which settings are used in the UK and the US, where the switch to the standard setting happens, and how to estimate the error from a wrong setting.

Time
40 minutes + 10 min homework
Course
Private Pilot Theory (ages 16+)
You need
Paper, a pencil and this page
Marked
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an approved training organisation, and nothing here counts towards a pilot licence or replaces a CAA-approved course and the CAA’s own exams. Rules and values on this page are given as of November 2026. Always check the current official source (the UK CAA) before relying on them.

How to use this lesson

This is adult-level theory (16+). It explains the rules for understanding; it is not instruction in setting a real altimeter. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why does it make sense for aircraft flying high and fast to share one standard pressure setting rather than local ones?”
  4. Later: the homework, then the practice test.

Watch out for

  • Getting 'high to low' the wrong way round. Flying into lower pressure without resetting: the altimeter over-reads – look out below.
  • Using the US 18,000 ft figure in the UK. UK transition altitude is 3,000 ft outside controlled airspace (5,000–6,000 ft within).
  • Mixing up altitude, height and flight level. QNH → altitude (AMSL); QFE → height (above aerodrome); 1013 → flight level.

Hands-on: Draw two columns of 'air' on paper – one over a high-pressure area, one over a low. Mark where the 1,000 ft pressure line would sit in each, and show why an altimeter set for the high area reads too much in the low area.

What you will learn

  • I can explain why the altimeter setting must be changed during a flight.
  • I can state what each setting gives: altitude, height or flight level.
  • I can state where the change to the standard setting happens in my country.
  • I can estimate the altitude error from a pressure difference using the rule of thumb.

Key words

QNH
The pressure setting that makes the altimeter read altitude above mean sea level.
QFE
The setting that makes the altimeter read height above the aerodrome – zero on the ground there.
flight level (FL)
Pressure altitude in hundreds of feet with 1013 hPa set: FL35 = 3,500 ft on the standard setting.
transition altitude
The altitude at or below which QNH is used; above it, aircraft use 1013 hPa and flight levels.

The big ideas

An altimeter is a barometer: it measures air pressure and shows it as height. Because sea-level pressure changes from day to day and place to place, the pilot sets a reference pressure on the instrument. Set the wrong one and the reading is wrong.

The CAA's Skyway Code (as of November 2026) describes three settings. QNH gives altitude above mean sea level. QFE gives height above the aerodrome, so the altimeter reads zero on the ground there. Above the transition altitude, aircraft set the standard 1013 hPa and fly flight levels. The transition altitude is 3,000 ft AMSL outside controlled airspace, and normally 5,000 or 6,000 ft within or below it; the transition level is at least 1,000 ft above, and the lowest VFR flight level is normally FL35. The Skyway Code also describes the Regional Pressure Setting, the lowest forecast pressure in a region, which normally makes the altimeter under-read.

A useful rule of thumb from the Skyway Code: 1 hPa is about 27 ft. So a setting 10 hPa wrong gives an error of about 270 ft. And the FAA's handbook memory aid applies everywhere: 'going from a high to a low, look out below' – flying into lower pressure without resetting makes the altimeter over-read, so the aircraft is lower than shown. The US uses inches of mercury and a much higher switch-over (18,000 ft); its lesson is separate.

Read-through: the teaching steps

  1. The altimeter is a barometer

    Pressure falls as you climb. The altimeter turns pressure into a height reading, but it needs a reference pressure. Change the reference and the same aircraft shows a different number.

    0 ft15 °C5,000 ft5 °C10,000 ft−5 °CSea level pressure 1013.25 hPaAir column
    The International Standard Atmosphere (ISA) – a reference, not the real weather on any day.
  2. Three settings

    • QNH → altitude above mean sea level (used near the ground and for terrain clearance).
    • QFE → height above the aerodrome (reads zero on the ground there).
    • 1013 hPa → flight levels (used above the transition altitude, so everyone shares one setting).
  3. Where the switch happens

    • Transition altitude: 3,000 ft AMSL outside controlled airspace; normally 5,000 or 6,000 ft within or below it.
    • Transition level: at least 1,000 ft above the transition altitude.
    • Lowest VFR flight level: normally FL35.

    Climbing through the transition altitude, set 1013 hPa; descending through the transition level, set QNH.

  4. High to low, look out below

    If an aircraft flies from high pressure into low pressure without resetting, the altimeter reads higher than the true altitude. The aircraft is lower than the pilot thinks – dangerous near hills. The Skyway Code also notes that the Regional Pressure Setting (lowest forecast) normally under-reads, giving a safety margin.

  5. Rule of thumb for errors

    1 hPa ≈ 27 ft (Skyway Code).

    Error (ft) ≈ pressure difference (hPa) × 27.

    Example: QNH 1003 set as 1013 → 10 hPa × 27 = about 270 ft over-reading.

Try it: the altimeter

Move the controls and watch the instruments, then try reading them.

Try the real thing: CAA Skyway Code (CAP 1535) (opens in a new tab).

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Air Law lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the CAA, any flying school, testing agency or exam board.