▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Altimeter setting rules: QNH, QFE and 1013.2 hPa (UK) vs 29.92 inHg and 18,000 ft (US) – Private Pilot Theory aviation lesson

Lesson 15 of 228 in the Private Pilot Theory course (ages 16+)

US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version

An altimeter only reads correctly if it is set to the right pressure. Learn which settings are used in the UK and the US, where the switch to the standard setting happens, and how to estimate the error from a wrong setting.

Time
40 minutes + 10 min homework
Course
Private Pilot Theory (ages 16+)
You need
Paper, a pencil and this page
Graded
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test. Rules and values on this page are given as of November 2026. Always check the current official source (the FAA) before relying on them.

How to use this lesson

This is adult-level theory (16+). It explains the rules for understanding; it is not instruction in setting a real altimeter. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why does it make sense for aircraft flying high and fast to share one standard pressure setting rather than local ones?”
  4. Later: the homework, then the practice test.

Watch out for

  • Getting 'high to low' the wrong way round. Flying into lower pressure without resetting: the altimeter over-reads – look out below.
  • Using the UK 3,000 ft figure in the US. US switch-over is 18,000 ft MSL.
  • Mixing up altitude, height and flight level. Local setting → altitude (MSL); 29.92 → flight level; height above ground needs the terrain elevation.

Hands-on: Draw two columns of 'air' on paper – one over a high-pressure area, one over a low. Mark where the 1,000 ft pressure line would sit in each, and show why an altimeter set for the high area reads too much in the low area.

What you will learn

  • I can explain why the altimeter setting must be changed during a flight.
  • I can state what each setting gives: altitude, height or flight level.
  • I can state where the change to the standard setting happens in my country.
  • I can estimate the altitude error from a pressure difference using the rule of thumb.

Key words

altimeter setting
The local pressure setting (in inHg) that makes the altimeter read altitude above mean sea level.
standard setting (29.92 inHg)
The setting used at and above 18,000 ft MSL, so the altimeter reads pressure altitude (flight levels).
flight level (FL)
Pressure altitude in hundreds of feet with 29.92 inHg set: FL180 = 18,000 ft on the standard setting.
18,000 ft MSL
The altitude where US aircraft change from the local altimeter setting to 29.92 inHg (14 CFR 91.121).

The big ideas

An altimeter is a barometer: it measures air pressure and shows it as altitude. Because sea-level pressure changes from day to day and place to place, the pilot sets a reference pressure on the instrument. Set the wrong one and the reading is wrong.

14 CFR 91.121 (as of November 2026) sets the US rules. Below 18,000 ft MSL, the altimeter is set to the current reported setting of a station along the route and within 100 NM of the aircraft (or another appropriate station; for an aircraft without a radio, the departure airport elevation or a setting available before departure). At or above 18,000 ft MSL, the altimeter is set to 29.92 inHg and the aircraft flies flight levels. Because low pressure would bring FL180 too close to the altitudes below, 91.121(b) raises the lowest usable flight level when the setting is below 29.92 – for example FL185 for a setting between 29.91 and 29.42.

The FAA's Pilot's Handbook gives a rule of thumb: 1 inch of mercury is about 1,000 ft. So a setting 0.30 inHg wrong gives an error of about 300 ft. Its memory aid: 'going from a high to a low, look out below' – flying into lower pressure without resetting makes the altimeter read too high, so the airplane is lower than shown. The UK uses hectopascals and switches to the standard setting much lower (3,000 ft outside controlled airspace); its lesson is separate.

Read-through: the teaching steps

  1. The altimeter is a barometer

    Pressure falls as you climb. The altimeter turns pressure into a height reading, but it needs a reference pressure. Change the reference and the same aircraft shows a different number.

    0 ft15 °C5,000 ft5 °C10,000 ft−5 °CSea level pressure 29.92 inHgAir column
    The International Standard Atmosphere (ISA) – a reference, not the real weather on any day.
  2. Two settings

    • Local altimeter setting → altitude above mean sea level, below 18,000 ft MSL. Use a station along the route within 100 NM.
    • 29.92 inHg → flight levels, at and above 18,000 ft MSL, so everyone shares one setting.
  3. Where the switch happens

    • At or above 18,000 ft MSL: 29.92 inHg (Class A also begins at 18,000 ft MSL).
    • Below 18,000 ft MSL: local setting.
    • If the local setting is below 29.92, the lowest usable flight level rises: 29.91–29.42 → FL185; 29.41–28.92 → FL190, and so on (91.121(b)).
  4. High to low, look out below

    If an airplane flies from high pressure into low pressure without resetting, the altimeter reads higher than the true altitude. The airplane is lower than the pilot thinks – dangerous near terrain. The PHAK also notes that cold air does the same: in colder-than-standard air, true altitude is lower than indicated.

  5. Rule of thumb for errors

    1 inHg ≈ 1,000 ft (PHAK).

    Error (ft) ≈ pressure difference (inHg) × 1,000.

    Example: true setting 29.62 but 29.92 still set → 0.30 × 1,000 = about 300 ft over-reading.

Try it: the altimeter

Move the controls and watch the instruments, then try reading them.

Try the real thing: FAA Pilot’s Handbook of Aeronautical Knowledge, chapter 8: flight instruments (free PDF) (opens in a new tab).

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Air Law lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.