▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Aerodrome traffic zones (UK) and airport traffic patterns (US) – Private Pilot Theory aviation lesson

Lesson 14 of 228 in the Private Pilot Theory course (ages 16+)

UK version. UK spelling and units (hPa, metres, litres) and the UK CAA. · US version

Around an airfield, aircraft follow an agreed pattern so everyone knows where to look. Learn the UK aerodrome traffic zone and circuit, and the US traffic pattern, with their key dimensions.

Time
40 minutes + 10 min homework
Course
Private Pilot Theory (ages 16+)
You need
Paper, a pencil and this page
Marked
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an approved training organisation, and nothing here counts towards a pilot licence or replaces a CAA-approved course and the CAA’s own exams. Rules and values on this page are given as of November 2026. Always check the current official source (the UK CAA) before relying on them.

How to use this lesson

This is adult-level theory (16+). It explains patterns for understanding only – not as joining or flying instructions. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why might an airfield choose a right-hand circuit for one runway instead of the usual left-hand one?”
  4. Later: the homework, then the practice test.

Watch out for

  • Assuming circuits are always right-hand. Left-hand is the default unless the aerodrome or airport shows otherwise.
  • Forgetting to add field elevation. Pattern and circuit heights are above the aerodrome; add the elevation to get the altitude above sea level.
  • Thinking every UK aerodrome has an ATZ. The Skyway Code notes some busy aerodromes have none – check the chart.

Hands-on: Draw a runway on paper and add the five legs of a left-hand pattern with arrows. Then draw the same for a right-hand pattern. Label each leg.

What you will learn

  • I can describe the size of a UK aerodrome traffic zone (ATZ).
  • I can name the legs of a circuit or traffic pattern.
  • I can state the standard direction of turns.
  • I can work out a pattern or overhead-join altitude from the field elevation.

Key words

ATZ (UK)
Aerodrome traffic zone – a cylinder of protected airspace around a UK aerodrome.
circuit / traffic pattern
The standard path around a runway: upwind, crosswind, downwind, base and final.
downwind leg
The leg flown parallel to the runway, in the opposite direction to landing.
overhead join (UK)
Joining the circuit by flying over the aerodrome high above circuit height, then descending on the 'dead side'.
segmented circle (US)
A ground marker at non-towered airports that shows wind direction and pattern direction.

The big ideas

Airfields are busy places, and most collisions happen near them. Standard patterns help pilots predict where others will be.

In the UK, many aerodromes have an aerodrome traffic zone (ATZ). The CAA's Skyway Code (as of November 2026) describes it as a cylinder of airspace around the aerodrome, of 2 NM radius when the longest runway is 1,850 m or less and 2.5 NM when it is longer; the CAA's drone pages add that it extends to 2,000 ft above ground level. Where an ATC service is provided, permission is needed to enter. Aircraft fly a circuit – upwind, crosswind, downwind, base and final – turning left unless the aerodrome indicates otherwise. The Skyway Code gives no standard circuit height (pilots must know each aerodrome's), recommends the overhead join at uncontrolled aerodromes, and advises maintaining 2,000 ft above aerodrome height (or as the aerodrome specifies) when overhead. It does not recommend straight-in approaches, but if one is made, 'long final' is called at 4 NM and 'final' at 2 NM.

The US uses traffic patterns rather than ATZs. The FAA's AIM (4-3) says turns are to the left unless otherwise indicated, propeller aircraft fly the pattern at 1,000 ft AGL and large or turbine aircraft at not less than 1,500 ft AGL, aircraft enter the pattern in level flight abeam the midpoint of the runway at pattern altitude, and the turn to final should be completed at least 1/4 mile from the runway. Education only.

Read-through: the teaching steps

  1. Why a standard pattern?

    If everyone flies the same path around an airfield, pilots know where to look for other traffic. The pattern also gives a steady, predictable approach to the runway.

    0927ApronTaxiwayCircuit (downwind leg)Final approach and departure along the runway
    Runway numbers are the runway's magnetic direction divided by 10. The circuit is flown around the runway.
  2. The legs

    • Upwind – along the runway direction after take-off
    • Crosswind – at right angles to the runway
    • Downwind – parallel to the runway, opposite to the landing direction
    • Base – at right angles, towards the runway
    • Final – lined up with the runway

    Turns are to the left unless the aerodrome indicates otherwise.

  3. The UK ATZ

    An ATZ is a cylinder around the aerodrome:

    • radius 2 NM if the longest runway is 1,850 m or less
    • radius 2.5 NM if longer
    • up to 2,000 ft above ground level

    Where an ATC service is provided, permission is needed to enter. Some busy aerodromes have no ATZ.

  4. Joining and circuit height (UK)

    • The Skyway Code gives no standard circuit height – know the aerodrome's.
    • Overhead join recommended at uncontrolled aerodromes; maintain 2,000 ft above aerodrome height (or as the aerodrome specifies) when overhead.
    • Joining aircraft normally give way to traffic already in the circuit.
    • Straight-in approaches are not recommended; if made, call 'long final' at 4 NM and 'final' at 2 NM.
  5. Signals on the ground

    At aerodromes with a signals area, a right-hand arrow shows a right-hand circuit is in use; in the absence of a signal, a left-hand circuit is the norm (Skyway Code). Non-radio arrivals should observe the signals square from overhead.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

Fly it yourself

Try this in our own First Flight trainer, with Mr Wilbur helping. It runs in your browser and is free.

Open First Flight

This is a learning tool, not flight training.

More practice

More Air Law lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the CAA, any flying school, testing agency or exam board.