▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Materials: wood, aluminium alloy and composites – Ground School Basics aviation lesson

Lesson 27 of 90 in the Ground School Basics course (ages 11–16)

UK version. UK spelling and units (hPa, metres, litres) and the UK CAA. · US version

Follow aircraft materials from wood and fabric to aluminium and carbon fibre, and weigh up the strengths and weaknesses of each.

Time
40 minutes + 10 min homework
Course
Ground School Basics (ages 11–16)
You need
Paper, a pencil and this page
Marked
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an approved training organisation, and nothing here counts towards a pilot licence or replaces a CAA-approved course and the CAA’s own exams.

For parents: how to use this lesson

Use PVA, not strong resins, for the hands-on activity. This lesson links to design and technology (materials properties) and GCSE physics. Every answer is marked straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “If composites do not corrode or suffer metal fatigue, why might an airline still choose an aluminium aircraft?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking composites are always lighter than metal. The handbook says lighter weight is the most cited advantage but is not automatic – it depends on the design.
  • Thinking no visible dent means no damage on a composite. Hidden delamination can spread in a cone below an impact; that is the biggest disadvantage.
  • Thinking the fibres and resin do the same job. The fibres carry most of the load; the matrix holds them and gives the shape.

Hands-on: Make two beams from strips of paper: one plain, one made of several strips glued together with PVA. Support each between two books and add coins to the middle until it sags. Compare how a "fibres in a matrix" layup changes stiffness.

What your child will learn

  • I can describe how aircraft materials changed from wood and fabric to metal and composites.
  • I can explain what a composite material is: fibres in a matrix.
  • I can give advantages and disadvantages of composites compared with metal.
  • I can explain why composite aircraft need extra lightning protection.

Key words

truss
A framework of tubes or struts, braced to make a rigid structure; early aircraft used wood, steel or aluminium tubing.
monocoque
A design where the outer skin carries almost all the loads, like an eggshell.
semi-monocoque
A design where the skin is supported by an inner framework of formers, bulkheads and stringers that shares the bending loads.
composite
A fibre-reinforced matrix: strong fibres (such as glass or carbon) held in a resin that gives the part its shape.
delamination
Layers of a composite coming apart inside the material, often hidden below the surface.
fatigue
Weakening of a material by repeated loading, which can start cracks.

The big ideas

The FAA's Pilot's Handbook of Aeronautical Knowledge traces how aircraft structures developed. Early aircraft used an open truss of wood, steel or aluminium tubing covered with cloth fabric; fabric later gave way to lightweight metals such as aluminium. Fuselages evolved from wooden trusses to monocoque shells, where the skin carries almost all the loads, and then to semi-monocoque designs, where an inner framework of bulkheads, formers and stringers helps the skin.

Composites are described by the handbook as fibre-reinforced matrix systems: the fibres carry most of the load and the matrix – usually epoxy resin in aircraft – holds them together and gives the shape. The most common fibres are fibreglass and carbon fibre. In 1965 the FAA certified the first all-fibreglass aircraft in the normal category, a Swiss sailplane, and by 2005 over 35 % of new aircraft were built from composites.

Each material has trade-offs. Composites do not corrode, do not suffer metal fatigue in the same way, and can be moulded into smooth, low-drag shapes. But damage can be hidden inside them, many epoxies weaken when hot, and they need metal mesh added to spread the energy of a lightning strike.

Read-through: the teaching steps

  1. Wood and fabric

    Early aircraft used an open truss frame of wood, steel or aluminium tubing, braced to make it rigid, and covered in cloth fabric. A truss is strong and simple, but the handbook notes its main drawback: it is not streamlined.

  2. Metal skins: monocoque and semi-monocoque

    In a monocoque design the skin carries almost all the loads – but it does not tolerate dents well. Most metal aircraft are semi-monocoque: bulkheads, formers and stringers support the skin and take some of the bending stress.

  3. What is a composite?

    A composite is made of fibres in a matrix. The fibres (glass or carbon) carry most of the load; the matrix (usually epoxy resin) holds the fibres together and gives the part its shape.

    • Fibreglass: good strength and impact resistance, but somewhat heavy
    • Carbon fibre: stronger than fibreglass, but poor impact resistance; it can be about 30 % lighter than an equivalent aluminium structure
  4. Advantages of composites

    • Can be lighter (though not automatically)
    • No corrosion
    • No metal fatigue and crack growth like metals
    • Very smooth skins and curved shapes that reduce drag
  5. Disadvantages of composites

    The handbook calls the lack of visible proof of damage the most important disadvantage: a knock can leave a cone of hidden delamination underneath. Many epoxies start to weaken above about 66 °C – a black-painted wing in the sun can reach about 104 °C, while white paint rarely goes above about 60 °C.

  6. Lightning protection

    Metal skins conduct electricity, spreading a lightning strike's energy. Composites need help: fine metal mesh is bonded to the skin – aluminium mesh on fibreglass and copper mesh on carbon fibre.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Physics of flight lessons · Ground School Basics course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the CAA, any flying school, testing agency or exam board.