Materials: wood, aluminum alloy and composites – Ground School Basics aviation lesson
Lesson 27 of 90 in the Ground School Basics course (ages 11–16)
US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version
Follow aircraft materials from wood and fabric to aluminum and carbon fiber, and weigh up the strengths and weaknesses of each.
- Time
- 40 minutes + 10 min homework
- Course
- Ground School Basics (ages 11–16)
- You need
- Paper, a pencil and this page
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test.
For parents: how to use this lesson
Use PVA, not strong resins, for the hands-on activity. This lesson links to design and technology (materials properties) and GCSE physics. Every answer is graded straight away with a worked explanation.
- Read what your child will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “If composites do not corrode or suffer metal fatigue, why might an airline still choose an aluminum aircraft?”
- Later: the homework, then the practice test.
Watch out for
- Thinking composites are always lighter than metal. The handbook says lighter weight is the most cited advantage but is not automatic – it depends on the design.
- Thinking no visible dent means no damage on a composite. Hidden delamination can spread in a cone below an impact; that is the biggest disadvantage.
- Thinking the fibers and resin do the same job. The fibers carry most of the load; the matrix holds them and gives the shape.
Hands-on: Make two beams from strips of paper: one plain, one made of several strips glued together with PVA. Support each between two books and add coins to the middle until it sags. Compare how a "fibers in a matrix" layup changes stiffness.
What your child will learn
- I can describe how aircraft materials changed from wood and fabric to metal and composites.
- I can explain what a composite material is: fibers in a matrix.
- I can give advantages and disadvantages of composites compared with metal.
- I can explain why composite aircraft need extra lightning protection.
Key words
- truss
- A framework of tubes or struts, braced to make a rigid structure; early aircraft used wood, steel or aluminum tubing.
- monocoque
- A design where the outer skin carries almost all the loads, like an eggshell.
- semi-monocoque
- A design where the skin is supported by an inner framework of formers, bulkheads and stringers that shares the bending loads.
- composite
- A fiber-reinforced matrix: strong fibers (such as glass or carbon) held in a resin that gives the part its shape.
- delamination
- Layers of a composite coming apart inside the material, often hidden below the surface.
- fatigue
- Weakening of a material by repeated loading, which can start cracks.
The big ideas
The FAA's Pilot's Handbook of Aeronautical Knowledge traces how aircraft structures developed. Early aircraft used an open truss of wood, steel or aluminum tubing covered with cloth fabric; fabric later gave way to lightweight metals such as aluminum. Fuselages evolved from wooden trusses to monocoque shells, where the skin carries almost all the loads, and then to semi-monocoque designs, where an inner framework of bulkheads, formers and stringers helps the skin.
Composites are described by the handbook as fiber-reinforced matrix systems: the fibers carry most of the load and the matrix – usually epoxy resin in aircraft – holds them together and gives the shape. The most common fibers are fibreglass and carbon fiber. In 1965 the FAA certified the first all-fibreglass aircraft in the normal category, a Swiss sailplane, and by 2005 over 35 % of new aircraft were built from composites.
Each material has trade-offs. Composites do not corrode, do not suffer metal fatigue in the same way, and can be molded into smooth, low-drag shapes. But damage can be hidden inside them, many epoxies weaken when hot, and they need metal mesh added to spread the energy of a lightning strike.
Read-through: the teaching steps
Wood and fabric
Early aircraft used an open truss frame of wood, steel or aluminum tubing, braced to make it rigid, and covered in cloth fabric. A truss is strong and simple, but the handbook notes its main drawback: it is not streamlined.
Metal skins: monocoque and semi-monocoque
In a monocoque design the skin carries almost all the loads – but it does not tolerate dents well. Most metal aircraft are semi-monocoque: bulkheads, formers and stringers support the skin and take some of the bending stress.
What is a composite?
A composite is made of fibers in a matrix. The fibers (glass or carbon) carry most of the load; the matrix (usually epoxy resin) holds the fibers together and gives the part its shape.
- Fibreglass: good strength and impact resistance, but somewhat heavy
- Carbon fiber: stronger than fibreglass, but poor impact resistance; it can be about 30 % lighter than an equivalent aluminum structure
Advantages of composites
- Can be lighter (though not automatically)
- No corrosion
- No metal fatigue and crack growth like metals
- Very smooth skins and curved shapes that reduce drag
Disadvantages of composites
The handbook calls the lack of visible proof of damage the most important disadvantage: a knock can leave a cone of hidden delamination underneath. Many epoxies start to weaken above 150 °F – a black-painted wing in the sun can reach 220 °F, while white paint rarely goes above 140 °F.
Lightning protection
Metal skins conduct electricity, spreading a lightning strike's energy. Composites need help: fine metal mesh is bonded to the skin – aluminum mesh on fibreglass and copper mesh on carbon fiber.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Graded by Classfern |
| Independent practice (three levels) | 11 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Physics of flight lessons · Ground School Basics course · All aviation practice tests · Aviation Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.