▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Inside a gasoline engine: pistons going up and down – Young Mechanics motor mechanics lesson

Lesson 3 of 40 in the Young Mechanics course (ages 8–11)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Look inside a gasoline engine and see how pistons moving up and down are turned into the round-and-round turning that drives the wheels.

Time
40 minutes + 10 min homework
Course
Young Mechanics (ages 8–11)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

A bicycle is a safe way to show the idea: the pedal cranks work just like a crankshaft. Please do not open a car's hood to look for these parts – they are hidden inside the engine. Every answer is graded straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think engines have more than one cylinder?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the pistons turn round and round. Pistons only slide up and down. It is the crankshaft that turns round.
  • Thinking all the pistons push at the same moment. They take turns, so the pushes are spread out and the engine runs smoothly.
  • Thinking the valves let fuel into the fuel tank. The valves are at the top of the cylinders. They let fuel and air into the cylinder and let used gases out.

Hands-on: Make a card crank model. Cut a circle of card about the size of a saucer and a strip of card about as long as your hand. Pin one end of the strip near the edge of the circle with a paper fastener, and pin the middle of the circle to a piece of cardboard so it can spin. Move the free end of the strip up and down in a straight line and watch the circle go round – that is how a piston turns a crankshaft. With an adult, you can also look at how pushing the pedals turns the cranks on a bicycle.

What your child will learn

  • I can name the cylinder, the piston, the connecting rod and the crankshaft.
  • I can explain that the pistons move up and down inside the cylinders.
  • I can explain how the crankshaft turns up-and-down movement into turning.
  • I can compare an engine's crankshaft with the pedals on a bicycle.

Key words

cylinder
A round tube inside the engine where the fuel and air burn. Most car engines have 3, 4 or 6.
piston
A metal plug that slides up and down inside a cylinder, pushed by the burning gas.
connecting rod
A strong metal arm that joins a piston to the crankshaft.
crankshaft
A bent shaft at the bottom of the engine. It turns round and round as the pistons push on it.
engine block
The heavy metal body of the engine that holds the cylinders.
valve
A little door at the top of a cylinder that opens to let air in or gases out.

The big ideas

If you could see inside a running gasoline engine, you would see metal parts moving up and down very fast. These are the pistons. Each piston sits snugly inside a round tube called a cylinder, a bit like a plunger inside a syringe.

Every time the fuel and air burn above a piston, the hot gas pushes the piston down hard. A metal arm called the connecting rod joins the piston to a bent shaft at the bottom of the engine called the crankshaft. As the piston is pushed down, it turns the crankshaft round – just as your legs push the pedals of a bicycle round.

So the engine turns an up-and-down movement into a round-and-round movement. The turning crankshaft is what eventually drives the wheels. Most car engines have 3, 4 or 6 cylinders, each with its own piston, taking turns to push so the turning stays smooth.

Read-through: the teaching steps

  1. The engine block and cylinders

    The engine block is the heavy metal body of the engine, often made of iron or aluminum. Inside it are the cylinders – smooth, round tubes. Most car engines have 3, 4 or 6 cylinders standing in a row or in two rows.

  2. The piston

    A piston is a short, round metal plug that fits inside a cylinder. It slides up and down. Rings around the piston seal the gap, so the hot gas pushes the piston instead of leaking past it.

    Look for the piston in the drawing on the lesson page.

    1 Intake2 Compression3 Power4 Exhaustinout
    The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes.
  3. The connecting rod

    The connecting rod is a strong metal arm. Its top end is joined to the piston and its bottom end to the crankshaft. When the piston is pushed down, the connecting rod passes the push on.

  4. The crankshaft: like bicycle pedals

    The crankshaft is a shaft with bends in it. Each bend is like a bicycle pedal crank. On a bike, your legs push down and the pedals go round. In an engine, the pistons push down and the crankshaft goes round.

    • Up-and-down movement goes in (from the pistons)
    • Round-and-round movement comes out (at the crankshaft)
  5. Valves at the top

    At the top of each cylinder are little doors called valves. One kind opens to let fuel and air in. The other kind opens to let used gases out to the exhaust. They open and close at exactly the right time, many times a second.

  6. Taking turns

    In a four-cylinder engine the four pistons do not all push at once. They take turns, so there is nearly always one piston pushing. This keeps the crankshaft turning smoothly. An engine at a steady speed can turn the crankshaft thousands of times a minute.

  7. Look, never touch

    A running engine has parts moving very fast and gets very hot. Mechanics look inside engines only when they are switched off, cold and safely stripped down in a workshop, wearing eye protection. Children learn from drawings and models, never from a real engine.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More How cars work lessons · Young Mechanics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.