Before the car: steam carriages and early engines – Vehicles and Technology motor mechanics lesson
Lesson 29 of 50 in the Vehicles and Technology course (ages 14+)
US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version
Travel back before 1886 to meet the steam carriages and the first gas engines, and see why steam lost the race to the internal combustion engine on the road.
- Time
- 35 minutes + 10 min homework
- Course
- Vehicles and Technology (ages 14+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.
How to use this lesson
Practice the question 'Where does the fuel burn?' – it is the quickest way to tell steam and gasoline engines apart. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Steam lost on the roads but won on the railways for over a century. Why might a technology be right for one job and wrong for another?”
- Later: the homework, then the practice test.
Watch out for
- Thinking steam vehicles never worked. They did work – Cugnot's and Trevithick's machines moved under their own power. They were slow, heavy and thirsty, which is why railways suited steam better.
- Thinking Otto's 1876 engine was put straight into a car. It was a heavy, slow factory engine on town gas. Lighter, faster engines had to be developed first.
- Mixing up the two kinds of combustion. Ask: where is the fire? Outside the cylinder (boiler) = external. Inside the cylinder = internal.
Hands-on: Draw two side-by-side diagrams on paper. Left: a steam engine – firebox, boiler, pipe and cylinder with piston. Right: an internal combustion engine – just a cylinder, piston, spark and fuel. Color the place where the fuel burns in red. Count how many large parts each one needs and write which would be easier to fit on a small vehicle.
What you will learn
- I can describe Cugnot's steam vehicle and Trevithick's Puffing Devil.
- I can explain the difference between external and internal combustion.
- I can say what Lenoir and Otto contributed to the engine.
- I can give reasons why steam was hard to use in small road vehicles.
Key words
- external combustion
- Fuel burns outside the engine, heating water in a boiler; the steam then drives the pistons.
- internal combustion
- Fuel burns inside the engine's cylinder, pushing directly on the piston.
- boiler
- A strong closed tank where water is heated to make steam under pressure.
- high-pressure steam
- Steam held at a pressure well above the air around us, so a small engine can give more push.
- atmospheric engine
- An early gas engine in which air pressure did much of the work on the return stroke. Noisy, with limited power.
The big ideas
Long before gasoline cars, inventors tried to replace the horse with steam. In 1769 Nicolas-Joseph Cugnot, a French Army engineer, built a working model of a steam vehicle to haul cannon, and in 1770 he showed a full-size "fardier à vapeur". It moved at a little over 2 miles per hour and had to stop every 15 minutes to add wood to its fire. The original still survives in the Musée des Arts et Métiers in Paris.
In Cornwall, Richard Trevithick built a high-pressure steam engine small enough to put on wheels. His Puffing Devil carried passengers up Camborne hill in 1801. Steam then found its real home on railways, where heavy boilers and big coal loads were less of a problem.
Meanwhile a different idea grew: burn the fuel inside the cylinder. Étienne Lenoir built a gas engine in 1859, and Nicolaus Otto's four-stroke engine first ran in 1876. Otto's engine was, in the Science Museum's words, "the first practical alternative to the steam engine" – and it is the ancestor of the engine in the 1886 motor car.
Read-through: the teaching steps
Why replace the horse?
Horses need food, rest and care, and they can only pull so much. Armies, farms and towns all wanted a machine that could pull loads all day. Steam engines already pumped water out of mines, so putting one on wheels was an obvious next step.
Cugnot's fardier, 1769–1770
Cugnot's vehicle was based on an army horse-cart. A third wheel and a copper boiler replaced the horse at the front, and a ratchet-like linkage drove that front wheel.
- Speed: a little over 2 mph
- Fuel: wood, added every 15 minutes, with a full stop each time
- Handling: difficult to maneuver
After several years of trials the army gave the project up.
Trevithick and high pressure, 1801
Early steam engines used low-pressure steam and were huge. Trevithick's high-pressure engine made more push from a smaller cylinder, so it could fit on a vehicle. His Puffing Devil carried passengers up Camborne hill in 1801, and in 1804 his Penydarren locomotive pulled 10 tons along a railway. Rails, not roads, became steam's great success.
External versus internal combustion
In a steam engine the fire is outside the cylinder: it boils water, and the steam pushes the piston. That needs a boiler, water and fuel – and time to raise steam.
In an internal combustion engine the fuel burns inside the cylinder and pushes the piston directly. There is no boiler, so the engine can be much lighter and can start quickly.
Lenoir and Otto
Étienne Lenoir built a combustion engine running on illuminating (town) gas in 1859. Nicolaus Otto and Eugen Langen founded their company in 1864 and showed an atmospheric gas engine at the 1867 Paris World Exhibition, winning a gold medal.
Otto's four-stroke engine first ran in March 1876. Its big step was squeezing (compressing) the fuel and air before igniting them – a principle still used in every car engine. The drawing on the lesson page shows the four strokes.
The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes. From factory engine to car engine
Otto's engine still ran on gas from a pipe and turned slowly: the Science Museum's replica gives 3 hp at 180 rpm. Gottlieb Daimler and Wilhelm Maybach both worked at Otto's Deutz company before making smaller, faster engines of their own. By 1886 the light internal combustion engine and the road vehicle came together in the first motor cars.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 11 min | Not assessed, self-checked |
| Worked examples and guided practice | 7 min | Graded by Classfern |
| Independent practice (three levels) | 8 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More History of the automobile lessons · Vehicles and Technology course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- Linda Hall Library – Nicolas-Joseph Cugnot
- Linda Hall Library – Richard Trevithick
- Technik Museum Speyer – The four-stroke engine
- Science Museum Group – Replica Otto four-stroke engine
- Mercedes-Benz Group – Company history 1886–1920
Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.