▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Volumetric and thermal efficiency – Motor Vehicle Theory motor mechanics lesson

Lesson 29 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Learn what volumetric and thermal efficiency mean, how to calculate them, and why most of the energy in a gasoline engine's fuel never reaches the wheels.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

This lesson uses US Department of Energy and fueleconomy.gov figures and example data for practice. The activity uses squared paper. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “If gasoline engines waste so much energy as heat, what could that heat be used for?”
  4. Later: the homework, then the practice test.

Watch out for

  • Forgetting the ÷ 2 for a four-stroke. Each cylinder fills once every two revolutions.
  • Thinking volumetric efficiency can never exceed 100%. With forced induction it can, because air is pushed in above atmospheric pressure.
  • Thinking most fuel energy moves the car. Only about a fifth reaches the wheels in a gasoline car; most becomes heat.

Hands-on: On squared paper, draw an energy bar for a gasoline car using 100 squares for the fuel's energy: color 20 squares for 'to the wheels' and the rest for losses, splitting them into engine heat and drivetrain and parasitic losses. Draw a second bar for an electric car's drive losses (about 15–20 squares lost). Compare.

What you will learn

  • I can define volumetric efficiency and calculate it for a four-stroke engine.
  • I can define thermal efficiency and calculate it from power and fuel energy.
  • I can explain what affects each kind of efficiency.
  • I can use published figures on where a gasoline car's energy goes.
  • I can compare engine and electric drive efficiency.

Key words

volumetric efficiency
Actual air drawn into the cylinders ÷ the air that would fill the swept volume, as a percentage.
thermal efficiency
Useful work from the engine ÷ energy supplied in the fuel, as a percentage.
forced induction
Pushing air into the engine above atmospheric pressure, with a turbocharger or supercharger.
parasitic loads
Energy used to drive parts such as the water pump and alternator.
energy content
The energy released by burning a given amount of fuel, for example MJ per liter.

The big ideas

An engine is an air pump and a heat engine at once, and it can be judged on both. Volumetric efficiency asks how well the cylinders fill with air: the more air, the more fuel can be burned and the more torque is produced. Thermal efficiency asks how much of the fuel's energy becomes useful work.

The honest answer for a gasoline car is: not much. US Department of Energy figures show that only about 20% of the energy released from the fuel reaches the wheels; the rest is lost to engine inefficiency, drivetrain friction and parasitic loads such as the water pump and alternator. fueleconomy.gov gives engine losses of 64–75% for a gasoline vehicle, against electric drive losses of only 15–20%.

This lesson explains both kinds of efficiency and teaches the calculations, using example figures for practice.

Read-through: the teaching steps

  1. Volumetric efficiency

    A four-stroke cylinder fills once every two crankshaft turns. Ideal air flow (liters per minute) = displacement (L) × rpm ÷ 2.

    Volumetric efficiency = actual air flow ÷ ideal air flow × 100%.

    Naturally aspirated engines typically reach 80–90% at best, highest near peak torque. See the intake stroke in the drawing on the lesson page.

    1 Intake2 Compression3 Power4 Exhaustinout
    The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes.
  2. What affects filling

    • Restrictions – air filter, throttle, ports and valves.
    • Valve timing – VVT helps filling across the rev range.
    • Temperature – hot air is less dense, so less mass fills the cylinder.
    • Speed – at high rpm there is less time to fill.
    • Forced induction – a turbocharger or supercharger can push volumetric efficiency above 100%.
  3. Thermal efficiency

    Thermal efficiency = useful power out ÷ fuel energy rate in × 100%.

    Fuel energy rate (kW) = energy content (kJ per liter) × liters per second.

    A gasoline engine's best thermal efficiency is often in the 30s per cent; diesels, with higher compression, usually do better.

  4. Where the energy goes

    US Department of Energy figures for a gasoline car: only about 20% of the fuel's energy reaches the wheels. fueleconomy.gov puts engine losses at 64–75%, mostly heat carried away by the exhaust and the cooling system. The rest goes in drivetrain friction and parasitic loads. Follow the path in the drivetrain drawing on the lesson page.

    EngineClutchTrans.DriveshaftDifferentialTurning force
    How the turning force gets from the engine to the driven wheels (rear-wheel drive shown).
  5. Improving efficiency

    Engineers raise thermal efficiency with higher compression (limited by knock in gasoline engines), direct injection, reduced friction, stop-start to cut idling and turbocharging to allow smaller engines. Hybrids help the engine work at its most efficient speeds. Electric motors avoid heat-engine losses altogether: fueleconomy.gov gives electric drive losses of 15–20%.

  6. Efficiency and the driver

    Thermal efficiency varies with load. At light load and in stop-start traffic it falls, because friction and pumping losses take a bigger share. Smooth driving, correct tire pressures and avoiding long idling all help an engine waste less.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Engines lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.