▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Heating and ventilation – Motor Vehicle Theory motor mechanics lesson

Lesson 104 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out how a car uses engine heat to warm the cabin, how the blower, blend door and recirculation work together, and how electric vehicles heat their cabins without waste engine heat.

Time
40 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

The lesson covers heat transfer and simple circuits. If the learner watches a real heater warm up, an adult must start and run the car outdoors, never in an enclosed space, and the learner only looks. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “An electric car may lose a noticeable part of its range heating the cabin in winter. Which ideas would you try first to keep people warm with less energy?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the heater uses extra fuel in a gasoline or diesel car. The heater core uses heat the engine would otherwise throw away through the radiator. Only the blower takes a little electrical power.
  • Thinking recirculation is best for clearing a misted screen. Recirculation traps moist cabin air. Fresh air, warm air on the glass and, where fitted, air conditioning clear mist faster.
  • Thinking an electric car's heater is "free" like a gasoline car's. In an electric car, every watt of heat comes from the battery, which is why heat pumps and heated seats are used to save range.

Hands-on: On a cold morning, sit in a parked car with an adult while the adult starts the engine outdoors (never in a closed garage). Watch the temperature gauge and note how long it takes before warm air comes from the vents. Ask the adult to try the defrost setting with fresh air and then with recirculation, and note which clears a fogged windshield faster. Look and feel the vents only; touch nothing under the hood.

What you will learn

  • I can trace the flow of coolant through the heater core and of air through the heater box.
  • I can explain how the blower speed, blend door, air distribution and recirculation are controlled.
  • I can explain why defogging matters for safety and how the system clears misted glass.
  • I can calculate the heat delivered to the cabin air and the effect of blower resistors.

Key words

heater core
A small radiator behind the dashboard. Hot engine coolant flows through it and warms the air blown across it.
blower motor
The electric fan that pushes air through the heater box. Its speed sets how much air reaches the cabin.
blend door
A flap that sends more or less of the incoming air through the heater, mixing hot and cool air to set the temperature.
recirculation
A setting that re-uses cabin air instead of drawing in fresh air from outside.
PTC heater
An electric heater whose resistance rises as it heats up, so it limits its own temperature. Used in many electric and hybrid vehicles.

The big ideas

A gasoline or diesel engine turns most of its fuel energy into heat. Most of that heat is thrown away through the radiator and exhaust, but some of it is put to good use: warming the cabin and clearing the windows. Wipers and the defroster are among the steps in Virginia's state safety inspection, because a fogged or frosted windshield is a real safety hazard.

The heating and ventilation system is simple in principle. Hot coolant from the engine flows through a small radiator, the heater core. A blower pushes air across it. Doors in the duct decide how much air goes through the core, where the air comes out, and whether it is fresh or recirculated.

Electric vehicles have no waste engine heat, so they use electric heaters or heat pumps instead. Their heaters may be part of the high-voltage system, which is for trained technicians only. This lesson explains how heating works; it is not a repair guide.

Read-through: the teaching steps

  1. Where the heat comes from

    Engine coolant is pumped round the engine, picking up heat. A thermostat keeps the engine near its working temperature by sending coolant to the radiator only when it is hot enough.

    The heater circuit is a separate loop: hot coolant leaves the engine, passes through the heater core behind the dashboard and returns to the pump. On most cars coolant flows through the core whenever the engine runs; some have a valve to shut it off.

    The coolant is hot and under pressure. Nobody opens the cooling system when it is warm, and work on it is for a qualified person.

  2. The heater box and blower

    Air enters through a grille below the windshield, usually through a cabin air filter. The blower motor pushes it into the heater box behind the dashboard.

    Blower speed is controlled by:

    • a resistor pack – resistors in series with the motor for the lower speeds, bypassed at full speed;
    • or an electronic module that varies the motor's supply smoothly.

    If only the top speed works, a failed resistor pack is a classic cause, because top speed bypasses the resistors.

  3. Temperature, distribution and recirculation

    Inside the heater box, flaps control the air:

    • Blend door – sends more or less air through the heater core and mixes it with air that bypasses it. This sets the temperature.
    • Distribution flaps – send air to the screen, face vents or footwell.
    • Recirculation flap – chooses fresh outside air or cabin air.

    Older cars move the flaps with cables; most modern cars use small electric motors (actuators) controlled by a module.

  4. Defogging and why fresh air matters

    Glass mists when warm, moist air from people's breath meets cold glass. To clear it the system:

    • blows warm air onto the screen, warming the glass;
    • uses fresh outside air, which in cold weather is usually drier than cabin air;
    • on cars with air conditioning, dries the air by running it over the cold evaporator first.

    Recirculation warms the cabin faster but traps moisture, so the screen mists sooner. That is why the defog setting usually switches to fresh air.

  5. Heating an electric vehicle

    Electric vehicles have very little waste heat, so they make it:

    • PTC heaters – ceramic elements whose resistance rises as they heat up, so they limit their own temperature. They may heat air directly or heat a coolant loop.
    • Heat pumps – work like air conditioning in reverse, moving heat from outside air into the cabin. They use less electricity than a plain heater for the same warmth.

    Cabin heating can noticeably reduce an electric car's winter range, which is why many have heated seats and steering wheels that warm the occupants directly. These heaters may run from the high-voltage battery: look, never touch.

  6. Common heating faults

    Typical symptoms and their usual causes, confirmed by a technician with the manufacturer's information:

    • No heat – low coolant, a stuck-open thermostat (engine never warms up), a blocked heater core or a stuck blend door.
    • Only top blower speed – failed resistor pack.
    • No blower at all – fuse, relay, motor or control module.
    • Air from the wrong vents – a failed flap actuator or broken linkage.
    • Sweet smell or misting inside – coolant leaking from the heater core.

    Coolant leaks and overheating are covered in the fault-finding lessons.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Heating and air conditioning lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.