Final drive and differential – Motor Vehicle Theory motor mechanics lesson
Lesson 60 of 131 in the Motor Vehicle Theory course (ages 16+)
US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version
Find out how the final drive gives the last speed reduction, how the differential lets the driven wheels turn at different speeds on a bend, and why an open differential struggles when one wheel loses grip.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.
How to use this lesson
This lesson explains final drives and differentials, with ratio and speed calculations. It is theory only; axle work is for trained technicians. Ratios quoted are typical values, not specifications for a particular vehicle. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think racing cars and off-road vehicles often use limited-slip or locking differentials, while most family cars do not?”
- Later: the homework, then the practice test.
Watch out for
- Thinking an open differential sends more torque to the wheel with grip. An open differential sends equal torque to both; the wheel with least grip sets the limit.
- Thinking the differential gears spin all the time. The pinions spin on their pin only when the wheel speeds differ.
- Forgetting that one wheel can turn at twice cage speed. If one wheel stops, the other must turn at 2 × cage speed to keep the average.
Hands-on: Walk round a circle chalked on a playground with a friend, side by side, holding a meter stick between you. Count steps: the outer person takes more. That is why wheels need a differential. Then cut a paper strip for each wheel's path on a bend (radius 5 m and 6.5 m at scale) and compare their lengths. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and cold, and only look.
What you will learn
- I can describe ring gear and pinion, hypoid and helical final drives.
- I can explain how a differential works using the average-speed rule.
- I can calculate final drive ratios, wheel speeds and wheel torque.
- I can explain the limits of an open differential and how limited-slip designs help.
Key words
- final drive
- The fixed gear reduction between the transmission output and the differential.
- ring gear (crown wheel)
- The large bevel gear in a rear axle, driven by the pinion and carrying the differential cage.
- differential
- A gear set that shares drive between two wheels while letting them turn at different speeds.
- open differential
- A plain differential that always gives equal torque to both wheels.
- limited-slip differential
- A differential that resists a speed difference so more torque can go to the wheel with grip.
The big ideas
After the transmission, drive passes through one more fixed reduction, the final drive. In a rear-wheel drive vehicle this is a ring gear and pinion, which also turns the drive through a right angle. In a front-wheel drive transaxle it is usually a pair of helical gears.
The final drive carries the differential. When a vehicle goes round a bend, each wheel follows a different curve and travels a different distance, so the driven wheels must turn at different speeds. The differential allows this while still driving both wheels.
This is explanation for understanding, not a repair guide. Axles and transaxles are heavy and are worked on only by trained technicians.
Read-through: the teaching steps
Final drive types
- Ring gear and pinion (rear axle): a small pinion on the driveshaft drives a large ring gear at 90°.
- Hypoid: the pinion sits below the ring gear center, lowering the shaft and floor; the teeth slide as they mesh, so a special extreme-pressure gear oil is used.
- Helical pair (front-wheel drive transaxle): the shafts are already parallel to the axle, so no 90° turn is needed.
Final drive ratio = driven teeth ÷ driver teeth, typically about 3:1 to 4.5:1 in cars.
How the turning force gets from the engine to the driven wheels (rear-wheel drive shown). Inside the differential
The ring gear is bolted to the differential case. Inside the case a cross-pin carries two (sometimes four) pinion gears. These mesh with two side gears, one splined to each half shaft.
Straight line and bends
On a straight road both side gears turn at the cage speed; the pinions do not spin on their pin and simply carry the side gears round.
On a bend the inner wheel slows. The pinions now roll round the slower side gear and push the other one faster by the same amount. The rule is:
cage speed = (left wheel speed + right wheel speed) ÷ 2
Torque sharing
An open differential always gives equal torque to the two wheels. That is fine when both have grip. But the torque each wheel can take is limited by its grip. If one wheel is on ice, it spins with very little torque, and the other wheel gets the same very little torque, so the car may not move. With one wheel stopped, the other spins at twice the cage speed.
Limited-slip and locking designs
- Clutch-type limited-slip: clutch plates between the cage and side gears resist a speed difference.
- Torque-sensing gear types: special gear geometry resists slip.
- Locking differential: locks both wheels together, used off road at low speed.
- Electronic: many cars brake a spinning wheel, which lets the differential send torque to the other side (see the brakes and traction control lessons).
Faults in theory
Whining that changes with road speed under load or coasting can point to worn final drive gears or bearings; clunks when taking up drive can come from worn differential parts or joints. A technician diagnoses by road test and inspection; axle and differential work needs specialist skills and equipment.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Graded by Classfern |
| Independent practice (three levels) | 13 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Transmission and drivetrain lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.