▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Axle shafts, constant-velocity joints and driveshafts – Motor Vehicle Theory motor mechanics lesson

Lesson 61 of 131 in the Motor Vehicle Theory course (ages 16+)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out how shafts and joints carry drive to wheels that steer and move up and down, why a universal joint makes speed ripple, and how constant-velocity joints avoid it.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.

How to use this lesson

This lesson explains drive shafts and joints with speed, torque and power calculations. It is theory only; drive shaft work is for trained technicians. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Front-wheel drive became common only after reliable CV joints were developed. Why do you think the joint was so important to that change?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a universal joint turns the output at a steady speed at any angle. Only a CV joint does that. A single universal joint makes the speed ripple twice per turn.
  • Thinking the boot is just a dust cover that does not matter. Once the boot splits, the grease goes and the joint wears out quickly.
  • Using kW instead of W in T = P × 60 ÷ 2πN. Change kW to W first (× 1,000).

Hands-on: Make a model universal joint from two bent paper clips linked at right angles, with a straw on each end as the shafts. Turn one straw at a steady rate with the joint bent and watch the other speed up and slow down. Add a second joint and see whether you can make the far straw turn steadily. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and cold, and only look, for example at a CV boot behind a front wheel.

What you will learn

  • I can describe where half shafts and driveshafts are used.
  • I can explain why universal joints cause speed variation and how two joints cancel it.
  • I can compare ball-type and tripod CV joints and say where each is used.
  • I can calculate shaft torque and power and universal-joint speed limits.

Key words

half shaft
A short shaft that carries drive from the differential to a wheel hub.
driveshaft
A long shaft that carries drive along the car to an axle.
universal joint
A cross-shaped joint (Hooke's joint) that lets a shaft drive at an angle, with some speed variation.
constant-velocity (CV) joint
A joint that drives at an angle with no speed variation.
boot
A flexible rubber cover that keeps grease in a joint and dirt out.

The big ideas

The transmission and differential are fixed to the car's body, but the wheels move up and down on their suspension, and front wheels also steer. The shafts that carry drive to them must therefore bend at joints and sometimes change length, all while carrying large torques.

Rear-wheel drive cars use a driveshaft along the car, usually with universal joints. Front-wheel drive cars use two short half shafts, each with a constant-velocity joint at both ends. Electric and four-wheel drive vehicles may use both kinds.

This is explanation for understanding, not a repair guide. Half shafts carry large torques and are worked on only by trained technicians with the vehicle properly supported.

Read-through: the teaching steps

  1. Where the shafts go

    • Front-wheel drive: two half shafts from the transaxle to the front hubs, often of different lengths.
    • Rear-wheel drive: a driveshaft from the transmission to the rear axle; independent rear suspension adds two short half shafts.
    • Four-wheel drive: driveshafts to both axles plus half shafts as needed.
    EngineClutchTrans.DriveshaftDifferentialTurning force
    How the turning force gets from the engine to the driven wheels (rear-wheel drive shown).
  2. The universal joint

    A Hooke's (universal) joint has two yokes joined by a cross with needle-roller bearings. It drives at an angle, but when the angle is θ the output speed rises and falls twice per turn, between input × cos θ and input ÷ cos θ. The average is the same as the input. At small angles the variation is small; at large angles it causes vibration.

  3. Canceling the ripple

    A driveshaft usually has a universal joint at each end. If the two joint angles are equal and the yokes on the shaft are lined up (in phase), the second joint's speed change exactly cancels the first, so the axle turns steadily. A sliding spline lets the shaft change length as the axle moves.

  4. Constant-velocity joints

    Front half shafts need large angles for steering, so universal joints would vibrate badly. CV joints keep output speed equal to input at any angle.

    • Ball-type (Rzeppa) joint: six balls in curved grooves between an inner and outer race; works at large angles; used at the wheel end.
    • Tripod joint: three rollers on a spider sliding in a housing; allows plunge (length change); usually used at the transmission end.

    Each joint is packed with special grease and sealed by a boot.

  5. Whirling and balance

    A long shaft spinning fast can bend and whirl at its critical speed. Designers keep the operating speed well below it by using stiff tubes, two-piece shafts with a center bearing, or lighter materials. Shafts are balanced with small weights, like wheels, to avoid vibration.

  6. Torque, power and faults

    Shaft torque T = P × 60 ÷ (2π × N), with P in watts and N in rpm.

    Fault theory: a split boot lets grease out and grit in, and the joint soon wears; a worn outer CV joint often clicks on full lock under power; a worn inner joint or universal joint can cause vibration or clunks when taking up drive. Diagnosis and repair are done by trained technicians.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Transmission and drivetrain lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.