Drivetrain layouts and their parts – Motor Vehicle Theory motor mechanics lesson
Lesson 52 of 131 in the Motor Vehicle Theory course (ages 16+)
US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version
Find out how power travels from the engine or motor to the road, how front-, rear-, mid-engine and electric layouts differ, and how to work out wheel speed and torque through the drivetrain.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (NHTSA and your own state’s rules) before relying on them.
How to use this lesson
This lesson explains drivetrain layouts and the arithmetic of gear ratios. It is theory for understanding; work on real drivetrains is for trained technicians. Any figures here are typical engineering values, not specifications for a particular vehicle. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “If you were designing a small city car, which layout would you choose, and what would you give up to get its advantages?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the transmission alone sets the wheel speed. The final drive is a second reduction. Always multiply the gear ratio by the final drive ratio.
- Thinking more torque at the wheels means more power. Gears trade speed for torque. Power stays the same (or falls slightly because of losses).
- Thinking electric cars have no transmission at all. Most have a single-speed reduction gear and a differential; they just do not need several ratios.
Hands-on: Draw three plan views of a car on paper: front-engine front-wheel drive, front-engine rear-wheel drive, and an electric car with one motor at the rear. Draw and label every drivetrain part in the order the power flows. Shade where the heaviest parts sit and estimate which axle carries more weight. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and cold, and only look.
What you will learn
- I can name the main parts of a drivetrain and say what each one does.
- I can compare front-wheel drive, rear-wheel drive, mid-engine and electric layouts.
- I can explain how layout affects weight distribution and traction.
- I can calculate overall ratio, wheel speed and wheel torque through a drivetrain.
Key words
- drivetrain
- All the parts that carry power from the engine or motor to the driven wheels.
- transaxle
- A transmission, final drive and differential combined in one case, used in most front-wheel drive cars.
- final drive
- The last fixed gear reduction before the wheels, usually built together with the differential.
- driveshaft
- A long shaft that carries drive along the vehicle, for example from a front transmission to a rear axle.
- overall ratio
- The gear ratio multiplied by the final drive ratio: how many times the engine turns for each turn of the wheels.
The big ideas
An engine or electric motor makes turning force (torque) at its output shaft. The drivetrain carries that torque to the driven wheels. On its way it is coupled and uncoupled (clutch or torque converter), changed in ratio (transmission), reduced again (final drive), shared between the left and right wheels (differential) and carried by shafts. The US Department of Energy sums up the transmission's job as transferring mechanical power to the wheels.
Where the engine sits and which wheels it drives is called the layout. Most cars today are front-engine, front-wheel drive. Rear-wheel drive, mid-engine and four-wheel drive layouts each bring different advantages. Electric cars change the picture again, because a motor can sit right beside the axle it drives.
This is explanation for understanding, not a repair guide. Drivetrain parts are heavy and work under high loads; work on a real vehicle is for trained technicians with proper equipment.
Read-through: the teaching steps
The chain of parts
Follow the power from the engine to the road. The drawing on the lesson page shows the order.
- Clutch (manual) or torque converter (automatic): lets the engine run while the car is still and takes up drive smoothly.
- Transmission: offers several ratios so the engine stays in its useful speed range.
- Driveshaft (rear-wheel drive only): carries drive along the vehicle.
- Final drive and differential: a fixed reduction, and a way to share drive between two wheels that turn at different speeds.
- Half shafts (axle shafts): carry drive out to each wheel hub.
How the turning force gets from the engine to the driven wheels (rear-wheel drive shown). Front-engine, front-wheel drive
Most small and medium cars mount the engine across the car (transverse). The transmission sits at one end of the engine, and the final drive and differential are in the same case, making a transaxle. Two short shafts with constant-velocity joints take drive to the front wheels, which also steer.
- Advantages: compact, no shaft along the floor, more cabin space, good traction because the engine weight sits over the driven wheels.
- Drawbacks: the front tires do both steering and driving, and weight moves off them when the car accelerates hard.
Front-engine, rear-wheel drive
The engine usually sits lengthways (longitudinal). The transmission is bolted behind it, a driveshaft runs under the floor, and the final drive and differential sit in the rear axle or in a unit fixed to the body.
- Advantages: steering and driving are split between the axles; weight moves onto the driven wheels when accelerating, which suits towing and powerful vehicles.
- Drawbacks: the tunnel for the shaft takes cabin space, and there are more parts.
Mid-engine, rear-engine and four-wheel drive
A mid-engine car puts the engine between the driver and the rear axle, keeping mass near the center for sharp handling. A rear-engine car puts it behind the rear axle. Both usually use a transaxle.
Four-wheel drive and all-wheel drive send drive to both axles, using extra parts such as a transfer case or center differential. A later lesson covers them in detail.
Electric layouts
The US Department of Energy lists an electric traction motor, a power electronics controller and a transmission among the parts of a battery electric car. In many electric cars the transmission is a single fixed reduction gear with a differential, built into one unit with the motor. A motor gives strong torque from standstill across a wide speed range, so one ratio is often enough.
Some electric cars have a motor on each axle, giving all-wheel drive without any shaft between the axles. The high-voltage parts are for trained technicians only; look, never touch.
The main parts of a battery electric car. High-voltage parts (usually with orange cables) are for trained technicians only. Following the numbers
Each reduction multiplies torque and divides speed by the same ratio (ignoring friction losses).
- Overall ratio = gear ratio × final drive ratio.
- Wheel speed = engine speed ÷ overall ratio.
- Torque at the axle = engine torque × overall ratio (shared between the two driven wheels by the differential).
Real drivetrains lose a small part of the power as heat in gears and bearings, so measured figures are a little lower.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Graded by Classfern |
| Independent practice (three levels) | 13 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Transmission and drivetrain lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- US Department of Energy, Alternative Fuels Data Center – How do gasoline cars work?
- US Department of Energy, Alternative Fuels Data Center – How do all-electric cars work?
Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.