▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Drivetrain layouts and their parts – Motor Vehicle Theory motor mechanics lesson

Lesson 52 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out how power travels from the engine or motor to the road, how front-, rear-, mid-engine and electric layouts differ, and how to work out wheel speed and torque through the drivetrain.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson explains drivetrain layouts and the arithmetic of gear ratios. It is theory for understanding; work on real drivetrains is for trained technicians. Any figures here are typical engineering values, not specifications for a particular vehicle. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “If you were designing a small city car, which layout would you choose, and what would you give up to get its advantages?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the gearbox alone sets the wheel speed. The final drive is a second reduction. Always multiply the gear ratio by the final drive ratio.
  • Thinking more torque at the wheels means more power. Gears trade speed for torque. Power stays the same (or falls slightly because of losses).
  • Thinking electric cars have no transmission at all. Most have a single-speed reduction gear and a differential; they just do not need several ratios.

Hands-on: Draw three plan views of a car on paper: front-engine front-wheel drive, front-engine rear-wheel drive, and an electric car with one motor at the rear. Draw and label every drivetrain part in the order the power flows. Shade where the heaviest parts sit and estimate which axle carries more weight. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and cold, and only look.

What you will learn

  • I can name the main parts of a drivetrain and say what each one does.
  • I can compare front-wheel drive, rear-wheel drive, mid-engine and electric layouts.
  • I can explain how layout affects weight distribution and traction.
  • I can calculate overall ratio, wheel speed and wheel torque through a drivetrain.

Key words

drivetrain
All the parts that carry power from the engine or motor to the driven wheels.
transaxle
A gearbox, final drive and differential combined in one case, used in most front-wheel drive cars.
final drive
The last fixed gear reduction before the wheels, usually built together with the differential.
propeller shaft
A long shaft that carries drive along the car, for example from a front gearbox to a rear axle.
overall ratio
The gear ratio multiplied by the final drive ratio: how many times the engine turns for each turn of the wheels.

The big ideas

An engine or electric motor makes turning force (torque) at its output shaft. The drivetrain carries that torque to the driven wheels. On its way it is coupled and uncoupled (clutch or torque converter), changed in ratio (gearbox), reduced again (final drive), shared between the left and right wheels (differential) and carried by shafts. The US Department of Energy sums up the transmission's job as transferring mechanical power to the wheels.

Where the engine sits and which wheels it drives is called the layout. Most cars today are front-engine, front-wheel drive. Rear-wheel drive, mid-engine and four-wheel drive layouts each bring different advantages. Electric cars change the picture again, because a motor can sit right beside the axle it drives.

This is explanation for understanding, not a repair guide. Drivetrain parts are heavy and work under high loads; work on a real vehicle is for trained technicians with proper equipment.

Read-through: the teaching steps

  1. The chain of parts

    Follow the power from the engine to the road. The drawing on the lesson page shows the order.

    • Clutch (manual) or torque converter (automatic): lets the engine run while the car is still and takes up drive smoothly.
    • Gearbox: offers several ratios so the engine stays in its useful speed range.
    • Propeller shaft (rear-wheel drive only): carries drive along the car.
    • Final drive and differential: a fixed reduction, and a way to share drive between two wheels that turn at different speeds.
    • Driveshafts: carry drive out to each wheel hub.
    EngineClutchGearboxPropeller shaftDifferentialTurning force
    How the turning force gets from the engine to the driven wheels (rear-wheel drive shown).
  2. Front-engine, front-wheel drive

    Most small and medium cars mount the engine across the car (transverse). The gearbox sits at one end of the engine, and the final drive and differential are in the same case, making a transaxle. Two short shafts with constant-velocity joints take drive to the front wheels, which also steer.

    • Advantages: compact, no shaft along the floor, more cabin space, good traction because the engine weight sits over the driven wheels.
    • Drawbacks: the front tyres do both steering and driving, and weight moves off them when the car accelerates hard.
  3. Front-engine, rear-wheel drive

    The engine usually sits lengthways (longitudinal). The gearbox is bolted behind it, a propeller shaft runs under the floor, and the final drive and differential sit in the rear axle or in a unit fixed to the body.

    • Advantages: steering and driving are split between the axles; weight moves onto the driven wheels when accelerating, which suits towing and powerful cars.
    • Drawbacks: the tunnel for the shaft takes cabin space, and there are more parts.
  4. Mid-engine, rear-engine and four-wheel drive

    A mid-engine car puts the engine between the driver and the rear axle, keeping mass near the centre for sharp handling. A rear-engine car puts it behind the rear axle. Both usually use a transaxle.

    Four-wheel drive and all-wheel drive send drive to both axles, using extra parts such as a transfer case or centre differential. A later lesson covers them in detail.

  5. Electric layouts

    The US Department of Energy lists an electric traction motor, a power electronics controller and a transmission among the parts of a battery electric car. In many electric cars the transmission is a single fixed reduction gear with a differential, built into one unit with the motor. A motor gives strong torque from standstill across a wide speed range, so one ratio is often enough.

    Some electric cars have a motor on each axle, giving all-wheel drive without any shaft between the axles. The high-voltage parts are for trained technicians only; look, never touch.

    Traction battery pack (under the floor)Electric traction motorPower electronicsCharge port
    The main parts of a battery electric car. High-voltage parts (usually with orange cables) are for trained technicians only.
  6. Following the numbers

    Each reduction multiplies torque and divides speed by the same ratio (ignoring friction losses).

    • Overall ratio = gear ratio × final drive ratio.
    • Wheel speed = engine speed ÷ overall ratio.
    • Torque at the axle = engine torque × overall ratio (shared between the two driven wheels by the differential).

    Real drivetrains lose a small part of the power as heat in gears and bearings, so measured figures are a little lower.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Transmission and drivetrain lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.