▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Wheel balance and why wheels wobble – Garage Basics motor mechanics lesson

Lesson 48 of 70 in the Garage Basics course (ages 11–16)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out why a few grams of extra mass on a spinning wheel can shake a whole car, how balance weights fix it, and calculate the forces involved.

Time
40 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

Please hold and spin the bicycle wheel yourself if your child is young. A calculator helps with the force formula; remember to change grams to kilograms. Every answer is graded straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think a washing machine sometimes shakes badly when it spins a heavy towel on one side of the drum?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a few grams cannot matter. At speed, a few grams pull with tens of newtons, enough to shake the car.
  • Thinking the force doubles when the speed doubles. Force depends on speed squared, so it goes up four times.
  • Thinking balancing and alignment are the same. Balancing evens out the mass round the wheel; alignment sets the angles the wheels point at.

Hands-on: Stick a lump of modeling clay to the rim of a bicycle wheel held upside down by an adult, or to the edge of a spinning top or a paper plate on a pencil. Spin it slowly, then faster, and feel or watch the wobble grow. Then add an equal lump on the opposite side and spin again. Keep fingers away from the spokes.

What your child will learn

  • I can explain what an unbalanced wheel is.
  • I can explain the difference between static and dynamic imbalance.
  • I can calculate the force from an unbalanced mass using F = m × v² ÷ r.
  • I can explain why the shaking gets much worse at higher speed.

Key words

imbalance
Uneven spread of mass around a wheel, so one side is heavier than the other.
balance weight
A small weight fixed to the wheel rim to even out the mass around the wheel.
static imbalance
A heavy spot that makes the wheel hop up and down as it spins.
dynamic imbalance
Uneven mass across the width of the wheel, which makes it wobble from side to side as it spins.
centripetal force
The inward force needed to keep a mass moving in a circle. A heavy spot pulls on the wheel with an equal outward force.

The big ideas

No tire or wheel is made perfectly even. There may be a slightly thicker patch of rubber, a heavier part of the rim or the valve on one side. When the wheel spins slowly this does not matter. But at speed, even a few grams in the wrong place pull outwards with a surprisingly large force, which changes direction every turn. The result is a vibration that can be felt through the steering wheel or the seat.

The physics is the same as swinging a bucket round on a rope: anything moving in a circle needs a force pulling it toward the center. For a heavy spot on a wheel, F = m × v² ÷ r, where m is its mass, v its speed and r the radius. Because the speed is squared, doubling the speed makes the force four times bigger. That is why an unbalanced wheel may feel fine in town but shake on a fast road.

In a workshop, a technician spins the wheel and tire on a balancing machine, which measures where the heavy spot is. Small weights are then fixed to the rim opposite it so the mass is even all the way round. Wheels are usually balanced whenever a new tire is fitted. Unbalanced wheels also wear tires, suspension parts and wheel bearings faster.

Read-through: the teaching steps

  1. Moving in a circle needs a force

    A mass moving in a circle is always changing direction, so a force must pull it toward the center. On a balanced wheel, all these pulls cancel out. A heavy spot leaves one pull uncancelled, so the wheel is tugged toward that spot, round and round.

    Tread depthreplace at 2/32 inTread wear barTread blockGroove
    Tread depth is measured in the grooves. NHTSA says a tire should be replaced when the tread is worn down to 2/32 of an inch.
  2. The force formula

    force (N) = mass (kg) × speed² (m/s)² ÷ radius (m)

    A 20 g (0.02 kg) heavy spot at a radius of 0.2 m, moving at 20 m/s: 0.02 × 400 ÷ 0.2 = 40 N. That is like a 4 kg mass tugging on the wheel, many times every second.

  3. Speed squared

    Double the speed and the force goes up four times. Triple it and the force goes up nine times. A tiny imbalance at town speeds can become a strong vibration on a fast road. Often the shaking is worst at one particular speed, where it matches the natural bounce of the suspension.

  4. Static and dynamic

    • Static imbalance: a heavy spot in the middle of the tread. The wheel hops up and down.
    • Dynamic imbalance: uneven mass across the width, for example heavier on the inner edge. The wheel wobbles from side to side.

    A balancing machine measures both, and weights are placed on the inner and outer edges of the rim to correct them.

  5. Where you feel it

    An unbalanced front wheel usually shakes the steering wheel. An unbalanced rear wheel is more often felt through the seat or floor. A technician would also check for a bent rim, a damaged tire or worn suspension, which can feel similar.

  6. Inspection

    State safety inspections such as Virginia's check tires, wheels and rims. Balancing itself is done in a workshop with a balancing machine.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Wheels and tires lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.