Steering systems: rack and pinion – Garage Basics motor mechanics lesson
Lesson 30 of 70 in the Garage Basics course (ages 11–16)
US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version
Find out how turning the steering wheel moves a toothed bar sideways to point the front wheels, and work out steering ratios and lock-to-lock turns.
- Time
- 40 minutes + 10 min homework
- Course
- Garage Basics (ages 11–16)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.
For parents: how to use this lesson
A calculator helps. The rack and pinion model is the key idea: turning becomes sliding. Steering parts on a real car are safety-critical and are only worked on by qualified technicians. Every answer is graded straight away with a worked explanation.
- Read what your child will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think a big truck needs more turns of the steering wheel from lock to lock than a go-kart?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the steering wheel turns the road wheels directly through a shaft. The column turns a pinion, which slides the rack sideways. The rack moves the wheels through the rods and arms.
- Thinking both front wheels always point at exactly the same angle. In a corner the inner wheel turns more sharply than the outer wheel (Ackermann geometry).
- Thinking a higher steering ratio makes steering quicker. A higher ratio needs more steering wheel turning for the same wheel angle, so it is slower but lighter.
Hands-on: Make a model rack and pinion: cut a strip of corrugated card as the rack and a round piece of corrugated card (or a bottle top with ridges) as the pinion. Push a pencil through the center of the pinion, lay it on the rack so the ridges mesh, and turn the pencil. Measure how far the rack moves in one turn and compare it with the distance round the pinion.
What your child will learn
- I can describe how a rack and pinion turns rotation into side-to-side movement.
- I can name the main parts from the steering wheel to the road wheels.
- I can calculate how far the rack moves for one turn of the pinion.
- I can calculate and explain a steering ratio.
- I can explain why the inner front wheel turns more sharply than the outer one.
Key words
- pinion
- A small gear on the bottom of the steering column.
- rack
- A straight bar with teeth along it. The pinion meshes with it and slides it left and right.
- tie rod
- A rod joining each end of the rack to the steering arm on a wheel hub. In the UK it is called a track rod.
- steering ratio
- How many degrees the steering wheel turns for each degree the road wheels turn, for example 15:1.
- lock
- As far as the steering will turn. "Lock to lock" means from fully left to fully right.
The big ideas
Most cars steer with a rack and pinion. The steering wheel turns a shaft called the steering column. At its bottom end is a small gear, the pinion. The pinion meshes with the rack, a straight bar with teeth along one side. When the pinion turns, the rack slides sideways, just as a cog wheel rolling along a toothed track would move.
Each end of the rack is joined by a tie rod to a steering arm on the front wheel hub. As the rack slides left or right, the tie rods push and pull the arms, and the wheels pivot to point the car in a new direction. Ball joints at the ends of the rods let them move with the suspension.
The gearing means the driver turns the steering wheel a long way to move the wheels a little. That makes steering precise and lighter to turn. Steering is safety-critical: state safety inspections such as Virginia's include steering and suspension, and any inspection or repair is for a qualified technician.
Read-through: the teaching steps
From wheel to road
Follow the path: steering wheel → steering column → pinion → rack → tie rods → steering arms → front wheels. Joints in the column let it bend round other parts and collapse in a crash to protect the driver.
Turning rotation into sliding
The pinion turns; the rack slides. For each full turn of the pinion, the rack moves a distance equal to the circumference of the pinion's pitch circle (the circle where its teeth mesh):
rack travel per turn = π × pinion pitch diameter
Lock-to-lock turns
The rack can only slide so far each way. The number of steering wheel turns from full left to full right is:
turns lock to lock = total rack travel ÷ rack travel per turn
Many cars need about 2.5 to 3.5 turns lock to lock.
Steering ratio
The steering ratio compares the angle turned by the steering wheel with the angle turned by the road wheels. A ratio of 15:1 means 15° at the steering wheel for 1° at the wheels. A higher ratio makes steering lighter and less twitchy; a lower ratio makes it quicker.
The steering wheel as a lever
The driver's hands push on the rim of the steering wheel. Torque on the column = force × radius of the wheel. A larger steering wheel gives more torque for the same push, which is why old cars without power steering had big steering wheels.
Inner wheel turns more
In a corner, the inner front wheel follows a smaller circle than the outer one, so it must turn more sharply. The steering arms are angled so that the inner wheel automatically turns a little further. This is called Ackermann steering geometry, and it stops the tires scrubbing sideways.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Graded by Classfern |
| Independent practice (three levels) | 11 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Brakes, steering and suspension lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.