Lifting a vehicle safely: jacks, stands and lifts (theory) – Garage Basics motor mechanics lesson
Lesson 59 of 70 in the Garage Basics course (ages 11–16)
US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version
Understand the science and the safety rules behind raising a vehicle: how a hydraulic jack multiplies force, why a jack alone must never hold up a car, and how lifts stay balanced.
- Time
- 40 minutes + 10 min homework
- Course
- Garage Basics (ages 11–16)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.
For parents: how to use this lesson
This lesson is theory only. Please do not let young people use a jack or go under a raised vehicle. The syringe model is a safe way to show hydraulic force. Every answer is graded straight away with a worked explanation.
- Read what your child will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “HSE says most deaths happen under badly supported vehicles. Why do you think people still take the risk, and what would you say to them?”
- Later: the homework, then the practice test.
Watch out for
- Thinking a jack can hold a vehicle safely while someone is underneath. A jack is for lifting only. HSE says do not rely on jacks alone; the vehicle must be properly supported.
- Thinking a hydraulic jack gives extra force for free. Force is multiplied, but the small piston moves much further. Energy is not created.
- Thinking a vehicle on a lift stays balanced whatever is removed. Removing a heavy part moves the center of gravity, and the vehicle can tip.
Hands-on: Model a hydraulic jack with two plastic syringes of different sizes joined by a short tube full of water (a science-kit activity). Push the small syringe and feel how the large one moves less but pushes harder. Then balance a ruler on a pencil with coins on each end, and see what happens when you take a coin off one end – just like removing a heavy part on a lift. Never use a real jack.
What your child will learn
- I can explain why HSE says never to rely on a jack alone.
- I can explain how a hydraulic jack multiplies force.
- I can describe the safety principles HSE gives for stands and lifts.
- I can explain why removing a heavy part can unbalance a vehicle on a lift.
Key words
- jack
- A device for raising a vehicle a short way. It is for lifting only, never for holding a vehicle while someone is under it.
- axle stand
- A strong, adjustable stand that supports a raised vehicle. Called a jack stand in the US.
- vehicle lift
- A powered machine, such as a two-post lift, that raises a whole vehicle so trained staff can work beneath it.
- safe working load (SWL)
- The greatest load a piece of lifting equipment is designed to carry safely. It must never be exceeded.
- center of gravity
- The point where the whole weight of an object can be thought to act.
The big ideas
This is explanation for understanding, not a repair guide. Raising and supporting vehicles is work for trained people with the right equipment, and young people should never go under a raised vehicle.
HSE, which looks after workplace safety in Great Britain, says that most deaths in motor vehicle repair happen when someone is trapped under a vehicle that is not properly supported. A car weighs well over a metric ton. If it falls, there is no time to get out of the way.
This lesson explains the science of jacks, stands and lifts, and the principles in HSE's guidance on working under vehicles, so you understand why workshops follow such strict rules.
Read-through: the teaching steps
A jack is for lifting only
A jack raises a vehicle, but it is not designed to hold it up while someone is underneath. A hydraulic jack can slowly sink if a seal leaks; a jack can tip or slip if the ground is soft or the vehicle moves.
HSE's guidance is clear: do not rely on jacks alone. Once raised, a vehicle must be supported properly, for example on axle stands, before anyone goes near the underside.
How a hydraulic jack multiplies force
A hydraulic jack has a small piston and a large piston joined by oil. Pressure in the oil is the same everywhere, so:
force on large piston = force on small piston × (area of large ÷ area of small)
If the large piston has 10 times the area, it pushes with 10 times the force. The catch: the small piston must move 10 times as far, which is why the handle is pumped many times for a small rise.
Stands and the ground
HSE's principles for supporting vehicles include:
- use only stands with their proper locking pins;
- work on hard, level ground;
- chock the wheels that stay on the ground;
- use the vehicle manufacturer's lifting points;
- never exceed the safe working load.
Soft ground matters because the weight on a stand is spread over a small base. A small area means high pressure, which can push the stand into soft ground.
Vehicle lifts
Workshops often use two-post lifts, which hold the vehicle by arms under its lifting points. HSE says the arm locks must be engaged and the pads correctly placed, and the load kept balanced – especially when heavy parts are removed.
HSE also recommends that lifts are thoroughly examined by a competent person every 6 months. Vehicles with air suspension, cabs and tipping bodies must be propped, because they can drop.
Balance and the center of gravity
On a two-post lift, the vehicle balances on its arms like a seesaw on its pivot. Its center of gravity must stay between the arms.
If a heavy part, such as the engine at the front, is removed, the center of gravity moves toward the back. If it moves too far, the vehicle can tip off the lift. That is why HSE warns about balancing the load when heavy parts are removed.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Graded by Classfern |
| Independent practice (three levels) | 11 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Workshop safety and tools lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department
About this lesson
Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.