▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Hydraulics: how a small push becomes a big squeeze – Garage Basics motor mechanics lesson

Lesson 26 of 70 in the Garage Basics course (ages 11–16)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out how a liquid in a pipe passes pressure from the brake pedal to every wheel, and calculate how the force is multiplied.

Time
45 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

The syringe activity uses plain water only, never real brake fluid, which is harmful. A calculator helps with the pressure sums. Every answer is graded straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think brake systems use liquid in their pipes rather than air?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the liquid itself gets "stronger" in the pipes. The pressure stays the same throughout. The bigger force comes from the bigger piston area.
  • Thinking hydraulics give extra energy. The big piston moves a smaller distance. Force × distance stays the same, apart from losses.
  • Thinking a spongy brake pedal is normal. A soft or sinking pedal can mean air or a leak in the system. The car must be checked by a qualified technician before it is driven.

Hands-on: Fill two plastic syringes (no needles) with water over a sink and join them with a short length of clear plastic tube. With an adult, push one plunger and watch the other move. Then try with air in the syringes and feel the difference. If you have a small and a large syringe, compare how far each plunger moves.

What your child will learn

  • I can explain why liquids are used to pass force through brake pipes.
  • I can calculate pressure using pressure = force ÷ area.
  • I can explain how a small piston and a large piston multiply force.
  • I can explain why air in a brake system is dangerous.

Key words

pressure
Force spread over an area: force ÷ area. Measured in pascals (Pa) or newtons per square centimeter (N/cm²).
hydraulic
Worked by a liquid under pressure.
master cylinder
The small cylinder and piston pushed by the brake pedal. It puts the brake fluid under pressure.
caliper
The part at a disc brake with one or more pistons that squeeze the pads onto the disc.
incompressible
Cannot be squashed into a smaller volume. Liquids are almost incompressible; gases such as air are not.

The big ideas

When the driver presses the brake pedal, a gentle push becomes a squeeze of thousands of newtons at each wheel. The trick is hydraulics: using a liquid in sealed pipes to carry pressure.

Liquids are almost impossible to squash. Push on liquid in a closed system and the pressure rises everywhere in it equally (Pascal's principle). The pedal pushes a small piston in the master cylinder. That pressure travels through the brake pipes to bigger pistons at the wheels. Because pressure = force ÷ area, the same pressure acting on a bigger area gives a bigger force.

Nothing is free: the big pistons move a much shorter distance than the small one. Also, if air gets into the pipes, the air squashes and the pedal feels soft or sinks. Brake systems are safety-critical and are worked on only by qualified technicians; brake fluid is harmful and must not be handled by learners. This lesson is about the science.

Read-through: the teaching steps

  1. Pressure = force ÷ area

    Pressure tells you how concentrated a force is.

    pressure = force ÷ area

    A force of 800 N on a piston of area 4 cm² gives a pressure of 800 ÷ 4 = 200 N/cm².

    CaliperBrake discFluidPistonPadsDisc (edge on)
    A disc brake: fluid pressure pushes the piston, the pads squeeze the spinning disc, and friction turns movement into heat.
  2. Liquids pass pressure on

    A liquid in a closed system passes pressure equally in all directions, to every part of the system. So the pressure made at the master cylinder arrives, almost the same, at every wheel. This is Pascal's principle, named after the French scientist Blaise Pascal.

  3. Small piston, big piston

    At the wheel, force = pressure × area. If the caliper piston has an area of 20 cm² and the pressure is 200 N/cm², the force is 200 × 20 = 4,000 N. The master cylinder piston was only 4 cm², so the force has been multiplied by 20 ÷ 4 = 5.

  4. The pedal is a lever too

    Before the hydraulics, the pedal itself is a lever that multiplies the driver's push, often by about 4 times. Most cars also have a brake servo that uses engine vacuum or an electric pump to add more force.

  5. The trade-off

    The same volume of liquid leaves the master cylinder as arrives at the wheel. A large piston needs more liquid to move a little, so it moves a shorter distance. Force goes up; distance goes down. The work in and out stays the same (ignoring losses).

  6. Why air is dangerous

    Air is a gas and squashes easily. If air gets into the brake pipes, pressing the pedal squashes the air instead of pushing the pads, so the pedal feels spongy. Brake fluid also slowly absorbs water from the air over time, which lowers its boiling point. That is why manufacturers set times for the fluid to be changed by a technician. In Virginia, for example, the state safety inspection includes the service brakes and fluid levels (inspection rules are set by each state).

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Brakes, steering and suspension lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.