▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Fuel injection: getting the right mixture – Garage Basics motor mechanics lesson

Lesson 8 of 70 in the Garage Basics course (ages 11–16)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Find out how an engine's computer measures the air coming in, decides how much fuel to add, and sprays it in as a fine mist – thousands of times a minute.

Time
45 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

The activity uses water only. Fuel and fuel systems are never handled; this lesson is theory. Every answer is graded straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Before electronic injection, engines used carburetors. What do you think are the advantages of letting a computer control the fuel?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking the injector squirts a jet of liquid fuel. It sprays a very fine mist, so the fuel evaporates and mixes with the air quickly.
  • Thinking the ECM sets the fuel once and leaves it. It adjusts the fuel many times a second using its sensors and the oxygen sensor's feedback.
  • Forgetting that a cycle takes two turns. Each injector fires once per cycle, which is every two crankshaft turns in a four-stroke engine.

Hands-on: Compare a jet and a mist using water only: squeeze a few drops from a dropper onto a paper towel, then spray the same amount from a clean spray bottle onto another towel. Which spreads over a larger area? Then draw a flowchart: sensors → ECM → injectors → exhaust → oxygen sensor → back to the ECM, and explain the loop.

What your child will learn

  • I can name the main parts of a gasoline fuel system and say what each does.
  • I can explain the difference between port injection and direct injection.
  • I can explain how the engine control module uses sensors to keep the mixture right.
  • I can calculate the time available for each cycle and an injector's duty cycle.

Key words

fuel injector
An electrically opened valve that sprays a fine mist of fuel when the engine's computer tells it to.
engine control module (ECM)
The engine's computer. It controls the fuel mixture and ignition timing and monitors the engine.
port injection
Spraying fuel into the intake manifold, just before the inlet valve.
direct injection
Spraying fuel straight into the combustion chamber.
oxygen sensor
A sensor in the exhaust that tells the ECM whether the mixture was rich or lean. It is also called a lambda sensor.
pulse width
How long the injector is held open each time, usually a few milliseconds.

The big ideas

An engine burns its fuel best when the mass of air and the mass of fuel are in the right ratio – about 14.7:1 for gasoline. Too much fuel wastes it and makes pollution; too little makes the engine run badly and can overheat it. Fuel injection is the system that gets the mixture right.

The US Department of Energy lists the parts of a gasoline car's fuel system: a fuel tank, a fuel pump, a fuel line to the engine and a fuel injection system. Fuel is injected into the intake manifold or into the combustion chamber, mixes with air and is ignited by the spark plug. The electronic control module (ECM) controls the fuel mixture and ignition timing, and monitors the engine.

The ECM reads sensors many times a second: how much air is coming in, how fast the engine is turning, how hot it is, how far the driver has pressed the power pedal, and how much oxygen is left in the exhaust. It then works out exactly how long to open each injector. Fuel systems carry flammable fuel under pressure, so they are worked on only by trained technicians; this lesson is theory.

Read-through: the teaching steps

  1. From tank to engine

    The fuel pump, usually inside the tank, sends fuel along the fuel line to the engine. A filter keeps dirt out, because injectors have tiny holes that block easily. Find the engine in the drawing on the lesson page; the tank is usually under the rear seats.

    Engine (under the hood)WindshieldWheel and tireDoorTaillightsExhaustHeadlights
    The main parts you can find on almost every car.
  2. The injector

    An injector is a valve with a small electric coil. When the ECM sends a pulse of current, the coil lifts a needle off its seat and fuel sprays out through tiny holes as a fine mist. The mist has a huge surface area, so it evaporates and mixes with air quickly. The longer the pulse, the more fuel is sprayed.

  3. Port or direct

    • Port injection: the injector sprays into the intake manifold, just before the inlet valve. The fuel mixes with air on its way in.
    • Direct injection: the injector sprays straight into the combustion chamber at much higher pressure. It allows more precise control.

    Diesel engines always use direct injection.

  4. Sensors and the ECM

    The ECM uses information from sensors:

    • Air flow or manifold pressure – how much air is going in
    • Crankshaft position – engine speed and piston position
    • Coolant temperature – a cold engine needs a slightly richer mixture
    • Pedal position – how much power the driver wants
    • Oxygen sensor – whether the last mixture was rich or lean
  5. A closed loop

    The oxygen sensor in the exhaust lets the ECM check its own work. If the exhaust shows too much oxygen, the mixture was lean, so the ECM adds a little fuel; too little oxygen, and it takes some away. This feedback loop keeps the mixture close to 14.7:1, which the catalytic converter needs to work well.

  6. Timing the spray

    At 3,000 rpm a cycle takes two turns: 3,000 ÷ 2 = 1,500 cycles per minute, or 25 per second. So each cycle lasts 1 ÷ 25 = 0.04 s = 40 ms. If an injector opens for 4 ms in every 40 ms cycle, it is open 4 ÷ 40 × 100 = 10% of the time. That percentage is called the duty cycle.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Engines and fuel lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.