▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Batteries, motors and inverters: the electric drivetrain – Garage Basics motor mechanics lesson

Lesson 65 of 70 in the Garage Basics course (ages 11–16)

US version. US spelling and words (tire, gasoline, hood) and US rules such as state inspections. · UK version

Follow the energy from the battery to the wheels of an electric car and find out what the traction battery, inverter, motor and the other main parts each do.

Time
45 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Graded
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training program or a certification, and nothing here replaces an accredited automotive program, ASE certification or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

This lesson explains how an electric drivetrain works using US Department of Energy and HSE information. It contains no practical work: the high-voltage system is for trained technicians only. Every answer is graded straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Electric cars need only one gear while gasoline cars need five or more. What is it about electric motors that makes this possible?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking an electric car has no 12-volt battery. It has a low-voltage auxiliary battery for lights and electronics, kept charged by the DC/DC converter.
  • Thinking the battery sends AC straight to the motor. Batteries store DC. The inverter in the power electronics makes the AC that many motors need.
  • Thinking a switched-off electric car is safe to touch inside. HSE warns that parts can hold dangerous residual voltage after switch-off. Only trained technicians work on the high-voltage system.

Hands-on: Make a flow chart on card of the energy path in an electric car: mains supply → charge port → onboard charger → traction battery → power electronics (inverter) → motor → transmission → wheels. Add a side branch for the DC/DC converter and auxiliary battery, and color the parts that carry hundreds of volts orange, as a warning.

What your child will learn

  • I can name the main parts of an electric car's drivetrain.
  • I can describe the job of the traction battery, power electronics, motor, onboard charger and DC/DC converter.
  • I can explain why an inverter is needed between a DC battery and an AC motor.
  • I can use P = V × I to work out power in an electric drivetrain.
  • I can explain why only trained technicians work on the high-voltage system.

Key words

traction battery pack
The large battery that stores the electrical energy used to drive the car.
traction motor
The electric motor that turns the wheels.
inverter
Power electronics that turn direct current (DC) from the battery into the alternating current (AC) many motors use.
onboard charger
The part that converts AC from the mains supply into DC to charge the traction battery.
DC/DC converter
The part that turns high-voltage DC from the traction pack into low-voltage DC for accessories.
high voltage
In the motor trade, HSE counts 60–1500 V DC as high voltage. Electric car systems use up to 650 V DC.

The big ideas

An all-electric car has no engine, no fuel tank and no exhaust. The US Department of Energy describes it as using an electric traction motor instead of an engine, powered by a large traction battery pack that must be plugged in to charge.

Between the battery and the wheels sit some clever electronics. The battery stores direct current (DC), but many traction motors run on alternating current (AC), so a power electronics controller containing an inverter changes one into the other and controls the motor's speed and torque. An onboard charger turns AC from the mains into DC to fill the battery, and a DC/DC converter steps the high voltage down to run the lights and other accessories.

These systems work at up to 650 V DC – enough to kill. This lesson explains how the parts work together. It is not a repair guide: HSE says high-voltage work is only for trained technicians with vehicle-specific training. Orange cables mean look, never touch.

Read-through: the teaching steps

  1. The main parts

    The US Department of Energy lists these main parts of an electric car:

    • traction battery pack – stores the energy
    • power electronics controller – controls the motor's speed and torque
    • electric traction motor – turns the wheels
    • onboard charger and charge port – take in electricity from a charger
    • DC/DC converter – supplies low-voltage power
    • auxiliary battery – powers accessories
    • thermal system – keeps everything at the right temperature
    • transmission – carries the motor's power to the wheels

    See where they sit in the drawing on the lesson page.

    Traction battery pack (under the floor)Electric traction motorPower electronicsCharge port
    The main parts of a battery electric car. High-voltage parts (usually with orange cables) are for trained technicians only.
  2. The traction battery

    The traction battery is made of many cells joined together. Joining cells in series adds their voltages, so a pack can work at hundreds of volts. The pack stores energy, measured in kilowatt-hours (kWh). It also needs a thermal system, because batteries work best and last longest within a certain temperature range.

  3. DC, AC and the inverter

    A battery can only give direct current (DC), which flows one way. Many traction motors run on alternating current (AC), which reverses direction many times a second.

    The inverter inside the power electronics switches the DC on and off very quickly to make AC. By changing the frequency of the AC it changes the motor's speed, and by changing the current it changes the torque. Pressing the pedal to go faster really sends a signal to the power electronics asking for more torque.

  4. The motor and transmission

    An electric motor gives strong turning force from a standstill and works efficiently over a wide range of speeds. That is why most electric cars need only a single fixed gear ratio rather than a transmission with many gears. The transmission reduces the motor's high speed to a lower wheel speed and increases the torque.

  5. Charging and the DC/DC converter

    The mains supply is AC. The onboard charger converts it to DC and monitors the battery's voltage, current, temperature and state of charge while charging.

    The car's lights, screens and controls still run at low voltage, usually 12 V, like a gasoline car. The DC/DC converter steps the traction pack's high voltage down to keep the auxiliary battery charged and run the accessories.

  6. Power in the drivetrain

    Electrical power is voltage multiplied by current:

    • P = V × I (watts = volts × amps)
    • 1 kW = 1,000 W

    A high voltage lets the drivetrain deliver a lot of power with a smaller current, which means thinner cables and less heat. That is one reason traction packs work at hundreds of volts – and why they are so dangerous to touch.

  7. Why high voltage is for trained technicians only

    HSE says electric and hybrid vehicles currently use up to 650 V DC, and contact with live parts above 110 V DC can be fatal even when dry. Even after switch-off, parts can hold dangerous residual voltage, and a damaged battery can catch fire or release gases.

    High-voltage cables are usually orange. In a workshop, only trained technicians isolate and prove the system dead before any work. Learners look, never touch.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minGraded by Classfern
Independent practice (three levels)13 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Electric and hybrid basics lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by ASE, NHTSA, any state agency, any college, testing agency or exam board.