Wings: spars, ribs and stressed skin – Private Pilot Theory aviation lesson
Lesson 148 of 228 in the Private Pilot Theory course (ages 16+)
US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version
See how a wing is built from spars, ribs, stringers and skin, and how cantilever and strut-braced wings carry their loads into the fuselage.
- Time
- 45 minutes + 10 min homework
- Course
- Private Pilot Theory (ages 16+)
- You need
- Paper, a pencil and this page
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test. Rules and values on this page are given as of November 2026. Always check the current official source (the FAA) before relying on them.
How to use this lesson
This is adult-level theory (16+). Read it alongside the official handbooks; it is explanation for understanding, not training. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “What are the trade-offs between a strut-braced wing and a cantilever wing for a small airplane?”
- Later: the homework, then the practice test.
Watch out for
- Thinking ribs carry the main bending load. Ribs give the shape; the spars are the main beams that carry bending.
- Thinking all high-wing airplanes have struts. Many do (semi-cantilever), but a few high-wing types are full cantilever.
- Forgetting that a wing is often a fuel tank too. The handbook notes that fuel is often carried in the wing structure.
Hands-on: Build a paper wing: cut three rib shapes from card (a curved-top airfoil about 8 cm long), push two drinking straws through them as spars, and wrap a paper skin over the top. Press down gently on the tip with and without the straws. Which part makes the biggest difference to stiffness?
What you will learn
- I can name the main structural parts of a wing.
- I can explain the job of spars, ribs and stringers.
- I can compare cantilever and strut-braced (semi-cantilever) wings.
- I can describe the wing positions high, mid and low.
- I can say what else a wing often carries, such as fuel.
Key words
- spar
- The main lengthwise beam of a wing that carries most of the bending load.
- rib
- A shaped cross-piece that gives the wing its airfoil shape.
- stringer
- A light lengthwise strip that stiffens the skin.
- cantilever wing
- A wing that carries its loads to the fuselage without external struts.
- semi-cantilever wing
- A wing braced by external struts, usually attached about halfway along it.
The big ideas
The wings are the main lifting surfaces of an airplane. The PHAK (chapter 3) names their principal structural parts: spars, ribs and stringers, covered by a skin. Ribs give the wing its airfoil shape; the spars are the main beams that run from root to tip and carry the lift into the fuselage.
Wings can be mounted high, in the middle or low on the fuselage. Many high-wing airplanes use external struts attached roughly halfway out along the wing to carry flight and landing loads – a semi-cantilever design. A full cantilever wing, used on a few high-wing and most low-wing airplanes, carries all its loads internally with no struts.
The handbook also notes that fuel is often carried inside the wing structure. This lesson is for understanding how wings are built; it is not maintenance or engineering guidance.
Read-through: the teaching steps
The wing as a beam
In flight, lift pushes the wing up along its whole length while the fuselage holds the root. So the wing bends like a diving board with a load on it. The spar is the main beam that resists this bending.
An airfoil: the chord line joins the leading and trailing edges; the angle of attack is between the chord line and the relative airflow. Spars
Most wings have one or more spars running from the root to the tip. Under lift the top of the spar is squashed (compression) and the bottom is stretched (tension).
Ribs
Ribs run from the leading edge to the trailing edge. They give the wing its airfoil shape and support the skin between the spars.
Stringers and skin
Stringers run along the wing and stiffen the skin so it does not buckle. In a stressed-skin wing the skin shares the load with the spars.
Struts or no struts?
- Semi-cantilever: an external strut, attached about halfway out, carries loads to the fuselage. Common on high-wing airplanes.
- Full cantilever: no struts; the spar carries everything to the root. Used on a few high-wing and most low-wing airplanes.
What else is in the wing?
The handbook notes that fuel is often carried in the wing structure. The ailerons and flaps are attached to the trailing edge: ailerons outboard, flaps inboard.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Graded by Classfern |
| Independent practice (three levels) | 13 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Aircraft General Knowledge lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.