The vertical speed indicator – Private Pilot Theory aviation lesson
Lesson 164 of 228 in the Private Pilot Theory course (ages 16+)
US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version
See how the VSI uses a diaphragm and a calibrated leak to show climb and descent rate, why it lags, and how to read trend and rate.
- Time
- 45 minutes + 10 min homework
- Course
- Private Pilot Theory (ages 16+)
- You need
- Paper, a pencil and this page
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test. Rules and values on this page are given as of November 2026. Always check the current official source (the FAA) before relying on them.
How to use this lesson
This is adult-level theory (16+). Read it alongside the official handbooks; it is explanation for understanding, not training. Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why might a pilot be taught to use the VSI for trend first and rate second?”
- Later: the homework, then the practice test.
Watch out for
- Expecting the VSI to show a new rate instantly. The handbook gives a lag of about 6–9 seconds; trend shows first, rate later.
- Reading a steady zero as "level flight" when the static port may be blocked. A blocked static system gives a continuous zero.
- Multiplying when you should divide. Time = height ÷ rate; height = rate × time.
Hands-on: Make a "calibrated leak" model: blow up a balloon, pinch the neck and let air out through a pin-prick hole in tape. The pressure inside follows changes only slowly – like the VSI case.
What you will learn
- I can explain how a VSI works.
- I can tell the difference between trend and rate on a VSI.
- I can state the lag given in the handbook.
- I can say what a blocked static port does to the VSI.
- I can calculate times and height changes from a vertical speed.
Key words
- VSI
- Vertical speed indicator – shows rate of climb or descent in feet per minute.
- calibrated leak
- A tiny restriction that lets the case pressure follow the diaphragm pressure slowly.
- trend
- The immediate direction the needle moves, showing the rate is increasing or decreasing.
- rate
- The steady rate of climb or descent once the needle has settled.
- lag
- The delay before the needle shows the new steady rate.
The big ideas
The vertical speed indicator (VSI) shows how fast the aircraft is climbing or descending, in feet per minute. The PHAK (chapter 8) calls it a differential pressure instrument. Static pressure goes straight into a diaphragm, and also into the instrument case through a calibrated leak. When the aircraft climbs, the pressure in the diaphragm falls at once but the case pressure falls more slowly; the difference moves the needle.
The handbook describes three pieces of information: trend (the immediate direction the needle moves), rate (the stabilized reading) and lag (the delay before the reading is accurate). It gives a lag of about 6–9 seconds, longer in rough air or with rough control. An instantaneous VSI (IVSI) uses accelerometers to reduce the lag.
Because the VSI depends on a changing static pressure, a blocked static system gives a continuous zero reading. This is theory for understanding only.
Read-through: the teaching steps
A differential instrument
Static pressure feeds the diaphragm directly and the case through a calibrated leak. In a climb the diaphragm pressure drops immediately, the case pressure lags behind, and the difference shows as a climb.
The “six-pack”: the six basic flight instruments in their usual layout. Trend
The direction the needle starts to move shows at once whether the climb or descent rate is increasing or decreasing.
Rate and lag
After the change, the needle settles on the new rate in feet per minute. The handbook gives about 6–9 seconds for this; turbulence and rough control make it longer.
The IVSI
An instantaneous VSI adds accelerometers that respond to vertical acceleration, reducing the lag.
Blocked static
With no changing static pressure, the VSI reads zero continuously.
Using the numbers
Time (minutes) = height change ÷ vertical speed. Height change = vertical speed × time.
Example: 3,000 ft at 500 ft/min → 3,000 ÷ 500 = 6 minutes.
Try it: the vertical speed indicator
Move the controls and watch the instruments, then try reading them.
Try the real thing: FAA Pilot’s Handbook of Aeronautical Knowledge, chapter 8: flight instruments (free PDF) (opens in a new tab).
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Graded by Classfern |
| Independent practice (three levels) | 13 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Aircraft General Knowledge lessons · Private Pilot Theory course · All aviation practice tests · Aviation Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.