How does a new aircraft get certified? – Navigation and Technology aviation lesson
Lesson 77 of 90 in the Navigation and Technology course (ages 14+)
US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version
Before a new aircraft can carry passengers, its makers must prove to the national regulator that every part of the design meets strict safety rules. Follow the journey from drawing board to test flights to the factory line.
- Time
- 40 minutes + 10 min homework
- Course
- Navigation and Technology (ages 14+)
- You need
- Paper, a pencil and this page
- Graded
- Instantly, with explanations
Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test.
How to use this lesson
Sources: FAA 'How it works: aircraft certification' page and FAA airworthiness certification page. A good link to engineering design (NGSS ETS1: criteria, constraints and testing). Every answer is graded straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “New aircraft take years to approve. Is it worth the wait? What could go wrong if the process were rushed?”
- Later: the homework, then the practice test.
Watch out for
- Thinking a type certificate approves each aircraft built. It approves the design. The factory and each individual aircraft are checked separately.
- Thinking certification is just a few test flights. Most of the work is analysis and ground testing, along with many hours of flight testing, over several years.
- Thinking the rules are the same for a small two-seater and a big airliner. Different sizes and types of aircraft have different sets of standards, and new ideas can need special extra conditions.
Hands-on: Design a paper airplane and write your own 'certification basis' – three rules it must meet (for example, it must fly at least 3 m, land without breaking, and fly straight). Plan how you will prove each one, then run the tests five times each and record the results. Did your design 'pass'? What would you change?
What you will learn
- I can explain what a type certificate is and who issues it.
- I can describe the main stages a new design goes through, from agreeing the rules to test flying.
- I can explain the difference between approving a design and approving the factory that builds it.
- I can explain why the process takes years and why that makes flying safer.
Key words
- regulator
- The government body that sets and checks safety rules – the UK Civil Aviation Authority (CAA) or the US Federal Aviation Administration (FAA).
- type certificate
- The regulator's approval of an aircraft design and its parts.
- certification basis
- The agreed set of safety rules a particular new design must meet.
- means of compliance
- How the maker will prove each rule is met – by calculation, ground test, flight test or inspection.
- production certificate
- Approval for a factory to build copies of an approved design, with proper quality control.
The big ideas
Every new aircraft type must be approved by a regulator before it can enter service. In the US that is the Federal Aviation Administration (FAA). The FAA describes a seven-phase process shared between the manufacturer and the FAA. Early on, the FAA sets the certification basis – the set of rules the design must meet – and agrees with the manufacturer how each rule will be shown to be met.
The makers then prove every rule is met, using calculations, laboratory tests on parts, huge ground tests and many hours of test flying. Wings are bent until they nearly break, and test aircraft are flown to the edges of what they can do, with specially trained test pilots and engineers on board. The FAA inspects test aircraft to make sure they match the design, and oversees the testing. When it is satisfied, it issues the type certificate, which the FAA calls approval of the design of the aircraft and all component parts.
Approving the design is not the end. The FAA then issues a production certificate, authorizing mass production once it has reviewed the factory's quality controls, and each individual aircraft is inspected before it receives its airworthiness certificate. This careful, slow process is one reason flying is so safe.
Read-through: the teaching steps
Who decides?
Each country has a regulator. In the US it is the FAA; in the UK it is the CAA; in the European Union it is EASA. A design approved in one country is usually checked again (validated) by the others before it can fly there, though agreements between countries make this quicker.
Agree the rules first
Before building anything, the maker and the regulator agree the certification basis. Most rules come from existing airworthiness standards for that size of aircraft. A brand-new idea, such as a new kind of electric motor, may need special extra conditions written just for that design.
Plan how to prove it
For every rule, the maker states how it will show the rule is met:
- calculation or computer analysis
- laboratory tests of parts and materials
- full-size ground tests (for example, bending a wing)
- flight tests
- inspection of the finished aircraft
Ground tests
Huge tests happen on the ground. A complete airframe may be bent, twisted and loaded many times over to show it is strong enough and will not crack too soon. Jet engines are tested by firing objects into them and running them in heavy rain and hail. Fire, lightning and cabin evacuation are tested too.
Flight tests
Several test aircraft fly for many hours. Test pilots check stalls, very slow and very fast flight, flying with one of the jet engines shut down, heavy and light loads, hot and cold weather and wet runways. Every flight records huge amounts of data for the engineers.
Design approval, then the factory
When the FAA is satisfied, it issues the type certificate. Then the production certificate authorizes mass production, after the FAA reviews the factory's quality and process controls. Each finished aircraft is inspected before it gets its own airworthiness certificate.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Graded by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Graded by Classfern |
| Independent practice (three levels) | 11 min | Graded by Classfern |
| Exit ticket and talk question | 5 min | Graded by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all graded instantly.
More practice
More Big questions lessons · Navigation and Technology course · All aviation practice tests · Aviation Department
Sources and curriculum
Facts in this lesson were checked against:
- https://www.caa.co.uk/Commercial-industry/Aircraft/Airworthiness/Type-design-approvals/Type-Certificates-and-R
- https://faa.gov/newsroom/how-it-works-aircraft-certification [suggest key FAA-CERT] – "rigorous 7-phase proces
Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.