▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Math, Cookery, Programming and Art are open – explore →

Airspace design: airways, SIDs and STARs – Navigation and Technology aviation lesson

Lesson 26 of 90 in the Navigation and Technology course (ages 14+)

US version. US spelling and units (inHg, statute miles, US gallons) and the FAA. · UK version

The sky above a busy airport is not a free-for-all. It is designed like a road network, with motorway-style airways, set 'slip roads' out of the airport (SIDs) and set routes in (STARs). Find out how these routes keep traffic flowing safely and what airspace modernization is trying to change.

Time
40 minutes + 10 min homework
Course
Navigation and Technology (ages 14+)
You need
Paper, a pencil and this page
Graded
Instantly, with explanations

Education and interest only. Classfern teaches aviation as a school subject. It is not flight training, not an FAA-approved school, and nothing here counts towards a pilot certificate or replaces training with a certificated instructor and the FAA knowledge test.

How to use this lesson

Sources: FAA AIM chapter 5 (instrument departures and standard terminal arrivals) and chapter 1 section 2 (RNAV specifications). The '3 NM per 1,000 ft' figure is a rough rule of thumb used for the sum only. Every answer is graded straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “New flight paths can save fuel but may send aircraft over homes that were quiet before. Who should decide where flight paths go, and how?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking aircraft can fly anywhere they like near a busy airport. Around busy airports, controlled airspace and published routes keep traffic organized.
  • Mixing up SIDs and STARs. SID = departure (going out); STAR = arrival (coming in).
  • Thinking all airspace is controlled. Class G is uncontrolled; pilots there rely mainly on see and avoid.

Hands-on: Draw a map of an imaginary airport with one runway. Add a hill to the north and a town to the east. Design one departure route (SID) and one arrival route (STAR) that avoid the hill, keep away from each other and avoid flying low over the town. Explain your choices to someone else.

What you will learn

  • I can explain what controlled airspace, airways, SIDs and STARs are.
  • I can explain why standard departure and arrival routes reduce workload and radio calls.
  • I can describe how the UK divides its airspace into classes.
  • I can work out descent and climb sums used in route design.

Key words

airway
A corridor of controlled airspace joining busy areas, like a motorway in the sky.
SID
Standard Instrument Departure – a published route from the runway to the airway network.
STAR
Standard Terminal Arrival Route – a published route from the airway network towards the approach to the runway.
controlled airspace
Airspace where air traffic control gives clearances and keeps certain aircraft apart.
airspace class
A letter (A to G) showing what rules and services apply in a piece of airspace.

The big ideas

Around busy airports the airspace is carefully designed. Airways – corridors of controlled airspace – link one busy area to another, much like highways. Leaving an airport, aircraft follow a Standard Instrument Departure (SID): a published route from the runway up to the airway network. Arriving, they follow a Standard Terminal Arrival (STAR) from the airways down towards the approach to the runway. The FAA's Aeronautical Information Manual (AIM) explains that SIDs are designed mainly to make the system work better and to reduce pilot and controller workload, cutting radio calls and delays, while also giving clearance from obstacles. STARs streamline clearance delivery and join the en route network to the instrument approach.

STARs often include crossing altitudes and speeds so that arriving aircraft are neatly spaced. The AIM describes a 'descend via' clearance, which lets a crew descend along the published route while meeting each restriction, instead of a controller giving step-by-step instructions. US airways come in two layers: lower Victor airways based on VOR beacons, and higher jet routes, with newer satellite-based T-routes and Q-routes.

Much of this design is decades old, built around ground beacons. Today, satellite-based routes (performance-based navigation) allow SIDs and STARs to be placed more precisely; the AIM says public satellite-based SIDs and STARs normally use RNAV 1 or RNP 1 specifications. The aims include fewer delays, less fuel burned and, where possible, less noise for people living below.

Read-through: the teaching steps

  1. Roads in the sky

    Airways link busy regions, like main roads between cities. Inside them, air traffic control gives clearances and keeps aircraft apart. Routes are defined by beacons (as in the VOR drawing on the lesson page) or by satellite waypoints.

    090 radial360
    A VOR radial is a magnetic bearing FROM the beacon. The 090 radial runs east from the beacon.
  2. SIDs: the slip roads out

    A SID is a published route from a runway to the airway network.

    • It keeps departing aircraft clear of obstacles.
    • It keeps them clear of arrivals and other airports' traffic.
    • Because it is published, the controller can say just its name instead of a long list of instructions.
  3. STARs: the slip roads in

    A STAR brings aircraft from the airways towards the approach. Many include heights and speeds at certain points, so arriving aircraft are lined up in an orderly stream, a bit like cars merging in turn.

  4. Fewer words on the radio

    Imagine a busy airport with an aircraft leaving every two minutes. If each needed ten separate radio instructions, the frequency would be jammed. A named SID or STAR packs all those instructions into one short phrase – that is why the AIM says they reduce workload and communications.

  5. Airspace classes

    US airspace uses classes A, B, C, D, E and G (there is no class F in the US).

    • Class A covers high levels and is for IFR flights.
    • Classes B, C and D surround busy airports.
    • Class E is other controlled airspace.
    • Class G is uncontrolled.

    The letter tells pilots which rules and services apply.

  6. Redesigning the sky

    Old routes zig-zagged between beacons. Satellite navigation lets designers draw smoother, more precise routes, including continuous climbs and descents that save fuel. But concentrating routes can also concentrate noise over the same homes, so redesign involves public consultation and difficult trade-offs.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minGraded by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minGraded by Classfern
Independent practice (three levels)11 minGraded by Classfern
Exit ticket and talk question5 minGraded by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all graded instantly.

More practice

More Air traffic & surveillance lessons · Navigation and Technology course · All aviation practice tests · Aviation Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the FAA, any flying school, testing agency or exam board.