▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Bicycle gears and the chain – Young Mechanics motor mechanics lesson

Lesson 32 of 40 in the Young Mechanics course (ages 8–11)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out how the chain and the toothed wheels on a bicycle work together, and why changing gear makes it easier to ride up a hill.

Time
40 minutes + 10 min homework
Course
Young Mechanics (ages 8–11)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

The only maths is division of whole numbers. If you look at a real bicycle together, hold it steady and keep fingers away from the chain and the teeth. Every answer is marked straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “If you could design a bicycle for a very hilly town, what gears would you give it?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a big sprocket at the back makes the bicycle faster. A big back sprocket is the easy gear: easier to push, but the bicycle goes less far for each turn of the pedals.
  • Thinking the chain pushes the back wheel round from the bottom. The top of the chain is pulled tight by the chainring, and it is this pull that turns the sprocket.

Hands-on: Cut a big circle and a small circle from card and draw "teeth" round their edges: count them. Lay a loop of string round both like a chain and turn the big circle once. Count how many times the small circle turns. If you have a bicycle with gears, ask an adult to hold it while you count the teeth on the smallest and largest back sprockets. Keep fingers away from the chain.

What your child will learn

  • I can name the chainring, the sprockets and the chain.
  • I can explain how the chain passes turning from the pedals to the back wheel.
  • I can say why a low gear makes climbing a hill easier.
  • I can count teeth to work out how many times the back wheel turns.

Key words

chainring
The big toothed wheel at the pedals. The cranks turn it.
sprocket
A smaller toothed wheel on the back wheel. Many bicycles have several, from small to large.
teeth
The bumps round the edge of a chainring or sprocket. The chain links sit between them.
gear
A choice of chainring and sprocket. Changing gear moves the chain to a different size.
derailleur
The part that pushes the chain from one sprocket to another when the rider changes gear.

The big ideas

When you push the pedals, the cranks turn a big toothed wheel called the chainring. The chain wraps round the chainring and round a smaller toothed wheel, called a sprocket, on the back wheel. As the chainring turns, it pulls the chain, and the chain turns the sprocket and the back wheel.

The sizes of the toothed wheels matter. A big chainring pulling a small sprocket makes the back wheel spin round several times for each turn of the pedals. That is fast, but it is hard work. A bigger sprocket at the back makes pedalling easier, but the bicycle goes less far for each turn of the pedals.

Many bicycles have gears, so the rider can choose. An easy (low) gear helps to climb hills. A hard (high) gear helps to go fast on the flat. The chain must stay clean and oiled to run smoothly, and a grown-up looks after it.

Read-through: the teaching steps

  1. Chainring and sprocket

    The chainring is the big toothed wheel by the pedals. The sprocket is the small toothed wheel on the back wheel. The chain joins them. The drawing on the lesson page shows the same idea with two gears touching.

    Driving gear10 teethDriven gear30 teethfast
    Gear ratio = teeth on the driven gear ÷ teeth on the driving gear = 30 ÷ 10 = 3 to 1.
  2. Counting teeth

    Every chain link sits between two teeth. So when the chainring turns once, the chain moves on by the number of teeth on the chainring.

    If the chainring has 30 teeth and the sprocket has 15 teeth, the chain moves 30 teeth, and the sprocket turns 30 ÷ 15 = 2 times. The back wheel turns twice for each turn of the pedals.

  3. Hard gears

    A small sprocket at the back is a hard, or high, gear. The back wheel turns many times for each turn of the pedals, so the bicycle goes a long way. But each push needs more effort. High gears are good for going fast on flat ground.

  4. Easy gears

    A big sprocket at the back is an easy, or low, gear. The back wheel turns fewer times for each turn of the pedals, so the bicycle goes less far, but pushing is much easier. Low gears are good for starting off and climbing hills.

  5. Changing gear

    On a bicycle with gears, the rider moves a lever or twists a grip on the handlebars. A part called the derailleur gently pushes the chain onto a different sprocket. Riders change gear while pedalling gently, never while the bicycle is standing still.

  6. Looking after the chain

    A chain works best when it is clean and lightly oiled. A dry or rusty chain is noisy and wears out the teeth. Fingers can be trapped between the chain and the teeth, so keep hands well away from a moving chain. A grown-up or a bicycle mechanic looks after it.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Bikes and motorbikes lessons · Young Mechanics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.