Units and conversions in the workshop – Motor Vehicle Theory motor mechanics lesson
Lesson 17 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Practise the conversions a technician meets every day: millimetres and inches, bar and psi, N·m and lbf·ft, kW and horsepower, litres and gallons, °C and °F.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson is maths practice with workshop units. The example values are for practice only; real specifications come from the manufacturer. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think many countries still use a mix of metric and imperial units in motoring?”
- Later: the homework, then the practice test.
Watch out for
- Multiplying when you should divide. Ask: is the new unit smaller (bigger number) or larger (smaller number)? Then estimate to check.
- Converting temperatures by multiplying only. °F = °C × 9/5 + 32: the + 32 matters.
- Using the American gallon for imperial figures. 1 imperial gallon = 4.546 litres; the gallon used in America is smaller.
Hands-on: Make a conversion card for a workshop wall on stiff paper: length, pressure, torque, power, volume and temperature, each with its factor and one worked example. Test it on a family member by asking them to convert three values using only your card.
What you will learn
- I can use SI prefixes such as milli and kilo.
- I can convert lengths between millimetres and inches.
- I can convert pressure, torque and power between metric and imperial units.
- I can convert temperatures between °C and °F.
- I can check a conversion by estimating.
Key words
- SI unit
- A unit in the international system: metre, kilogram, second, newton, pascal, joule, watt.
- prefix
- A word part that multiplies a unit: milli (÷1,000), centi (÷100), kilo (×1,000), mega (×1,000,000).
- conversion factor
- The number used to change one unit into another, such as 25.4 mm per inch.
- imperial units
- Older units such as inches, pounds, psi and gallons, still used alongside metric units.
- thou
- One thousandth of an inch (0.001 in), used for precise inch measurements.
The big ideas
A technician in Britain works in millimetres, newton-metres, bar and litres – but meets inches, psi, lbf·ft and horsepower in older data, imported vehicles and everyday speech. Getting a conversion wrong can mean a wrongly tightened bolt or a wrongly inflated tyre, so conversions are done carefully and checked.
This lesson collects the conversion factors used most in workshops, shows how to use them, and how to check an answer by estimating. The values in the examples are practice numbers; real specifications always come from the manufacturer's data.
Read-through: the teaching steps
Prefixes
- milli (m) = ÷1,000 – 1 mm = 0.001 m
- centi (c) = ÷100
- kilo (k) = ×1,000 – 1 kW = 1,000 W; 1 kPa = 1,000 Pa
- mega (M) = ×1,000,000 – 1 MPa = 1,000,000 Pa
Convert to the same prefix before adding or comparing values.
Length
- 1 in = 25.4 mm (exact)
- 1 thou = 0.001 in = 0.0254 mm
- 1 mile = 1.609 km
Inches → mm: multiply by 25.4. mm → inches: divide by 25.4.
Pressure and torque
- 1 bar = 100 kPa ≈ 14.5 psi
- 1 lbf·ft = 1.356 N·m
bar → psi: × 14.5. N·m → lbf·ft: ÷ 1.356.
Power and volume
- 1 hp ≈ 0.746 kW (mechanical horsepower)
- 1 litre = 1,000 mL
- 1 imperial gallon = 4.546 litres
kW → hp: ÷ 0.746.
Temperature
- °F = °C × 9/5 + 32
- °C = (°F − 32) × 5/9
Water freezes at 0 °C (32 °F) and boils at 100 °C (212 °F) at sea level. A warm engine's coolant runs at around 90 °C (194 °F).
Checking by estimating
Before trusting a calculator:
- 25.4 is about 25, so 4 in ≈ 100 mm;
- 14.5 is about 15, so 2 bar ≈ 30 psi;
- 1.356 is about 1.4, so 100 N·m ≈ 70 lbf·ft;
- converting to a smaller unit gives a bigger number.
If the answer is far from the estimate, check whether you multiplied when you should have divided.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Tools and measurement lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.