▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Steering racks, columns and joints – Motor Vehicle Theory motor mechanics lesson

Lesson 76 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Follow the steering from the driver's hands to the road wheels: the column and its joints, the rack and pinion or steering box, and the track rods and ball joints that link them to the hubs.

Time
45 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson explains how steering systems are built and how faults are judged. Steering is safety-critical: work on it is for trained technicians only. Values are dated; check the official source before relying on them. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why might a large lorry and a small city car be given very different steering ratios?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking a little free play at the steering wheel does not matter. Free play means the driver must turn further before the car responds. It points to wear somewhere in the chain of joints, and beyond a limit it is a fault.
  • Thinking a split gaiter is only cosmetic. The gaiter keeps dirt and water out of the rack or joint. Once it splits, grit gets in and the part wears quickly.
  • Thinking a higher steering ratio means quicker steering. A higher ratio means more turns of the steering wheel for the same road wheel movement: lighter, but slower.

Hands-on: Make a model rack and pinion: roll a strip of corrugated card into a short tube for the pinion and lay another strip flat as the rack. Turn the tube by one full turn while pressing it along the flat strip, and measure how far the strip moves. Compare it with π × the tube's diameter. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and cold, and only look – for example at the gaiters behind the front wheels with the steering turned to full lock by the adult.

What you will learn

  • I can name the parts that carry the steering movement from the steering wheel to the road wheels.
  • I can explain how a rack and pinion turns rotation into side-to-side movement.
  • I can calculate a steering ratio and the rack travel for one turn of the pinion.
  • I can explain why the column has universal joints and is designed to collapse in a crash.
  • I can describe how the MOT judges free play and worn joints in the steering.

Key words

rack and pinion
A small gear (the pinion) on the end of the steering column meshing with a toothed bar (the rack). Turning the pinion slides the rack left or right.
track rod
The rod that joins each end of the rack, or the steering linkage, to the steering arm on a hub.
ball joint
A ball in a socket that lets two parts move at an angle to each other while staying joined. Track rod ends contain ball joints.
steering ratio
How many degrees the steering wheel turns for each degree that the road wheels turn.
free play
Movement at the rim of the steering wheel before the road wheels begin to move.

The big ideas

When a driver turns the steering wheel, the movement passes through a chain of parts before the road wheels turn. The steering column carries it down from the wheel, through one or more universal joints. A steering gear – on most cars a rack and pinion – turns that rotation into a push or pull. Track rods then pass the push or pull to steering arms on the hubs, through ball joints that let everything move as the suspension rises and falls.

Every joint in that chain must be tight but free to swivel. Wear anywhere adds free play, so the driver has to turn the wheel further before anything happens, and a badly worn ball joint can, in the worst case, separate.

This lesson explains how the parts work and how faults are judged. It is not a repair guide: steering work is safety-critical and must be done only by a trained technician.

Read-through: the teaching steps

  1. The steering column

    The column joins the steering wheel to the steering gear. It usually has one or two universal joints, because the steering gear sits lower and to one side, so the shaft cannot run in a straight line. A flexible coupling or rubber element may also be fitted to stop road vibration reaching the driver's hands.

    Modern columns are designed to collapse or telescope in a frontal crash, so they are not pushed back towards the driver. Many also carry the steering lock, the airbag in the wheel boss, and switches for lights and wipers. The airbag means a column is never something to take apart without training.

  2. Rack and pinion

    On most cars the column ends in a small gear called the pinion. Its teeth mesh with a straight toothed bar, the rack, held in a tube across the car.

    Turning the pinion slides the rack left or right. For each full turn of the pinion, the rack moves a distance equal to the circumference of the pinion's pitch circle: π × pitch diameter. A rubber gaiter at each end keeps dirt and water out of the rack.

  3. Steering box and linkage

    Older cars and many heavy vehicles use a steering box instead of a rack. The column turns a worm inside the box, which swings a drop arm. A drag link or centre rod, with an idler arm on the other side, then passes the movement to the track rods.

    A steering box layout has more joints than a rack and pinion. That is one reason it can have more free play.

  4. Track rods and ball joints

    At each end of the rack, an inner ball joint lets the track rod swing up and down with the suspension. At the outer end, the track rod end is another ball joint, fixed to the steering arm on the hub.

    The track rod end is screwed onto the track rod, so its length can be changed. That is how a technician sets the toe. Each ball joint has a rubber dust cover to keep grease in and dirt out. A split cover lets grit in, and the joint then wears quickly.

  5. Steering ratio

    The steering ratio compares the turn of the steering wheel with the turn of the road wheels. If the steering wheel turns 360° and the road wheels turn 24°, the ratio is 360 ÷ 24 = 15:1.

    A high ratio makes steering lighter but needs more turns of the wheel; a low ratio is quicker but heavier. Typical car ratios are roughly 12:1 to 20:1. Some racks have a variable ratio, quicker towards full lock, by changing the tooth shape along the rack.

  6. How faults are judged in the MOT

    The MOT inspection manual (section 2, steering) sets limits for free play at the rim of the steering wheel. For a rack and pinion it should not be more than 13 mm, or 48 mm where there are several joints between the wheel and the rack. For other steering gear it is 75 mm. These figures are for a 380 mm steering wheel and are adjusted for larger or smaller wheels. Excessive free play is a major defect, or dangerous where safe steering is affected.

    A ball joint with excessive wear or free play is a major defect, and dangerous where there is a serious risk of it coming apart. A damaged gaiter or dust cover is minor; a missing one, or one that no longer keeps out dirt, is major.

The lesson, step by step

45 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task14 minNot assessed, self-checked
Worked examples and guided practice9 minMarked by Classfern
Independent practice (three levels)13 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Steering and suspension lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.