Spark plugs and glow plugs – Motor Vehicle Theory motor mechanics lesson
Lesson 127 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out why petrol engines need spark plugs and diesel engines use glow plugs, how plugs wear, and what a misfire can do to the exhaust system.
- Time
- 35 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
The activity uses a bicycle pump only. This lesson explains ignition; plug replacement is for trained technicians. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think diesel engines can manage without a spark, but petrol engines cannot?”
- Later: the homework, then the practice test.
Watch out for
- Thinking diesel engines have spark plugs. Diesels are compression-ignited; glow plugs only help cold starting.
- Thinking a glow plug makes a spark. It is a heater; the fuel still ignites from the heat of compression.
- Thinking a misfire only makes the engine rough. Unburnt fuel can overheat and damage the catalytic converter.
Hands-on: Squeeze test: hold your finger over the end of a bicycle pump and push the handle down quickly several times – feel the end get warm. This is the idea behind compression ignition. Then draw and label a spark plug and a glow plug side by side.
What you will learn
- I can explain the difference between spark ignition and compression ignition.
- I can describe how a spark plug works and how its gap and electrodes wear.
- I can explain what a glow plug does in a diesel engine.
- I can explain why a misfire matters for the catalytic converter.
Key words
- spark plug
- A part screwed into the cylinder head of a petrol engine that makes a spark to ignite the air–fuel mixture.
- spark gap
- The small gap between the plug's centre and side electrodes that the spark jumps across.
- glow plug
- An electric heater in a diesel engine's combustion chamber (or pre-chamber) that helps the engine start when cold.
- misfire
- A cylinder failing to burn its mixture properly on a power stroke.
The big ideas
Petrol and diesel engines ignite their fuel in different ways. The US Department of Energy describes a petrol car's engine as spark-ignited: fuel is mixed with air and ignited by the spark plug. A diesel is compression-ignited: fuel is injected into air that has been squeezed by the piston until it is hot enough to ignite the fuel on its own. So petrol engines need spark plugs, and diesels do not.
A spark plug has a centre electrode and an side electrode with a small gap between them. The ignition system sends a very high-voltage pulse to the plug at exactly the right moment, and the spark jumps the gap. Every spark erodes the electrodes slightly, so over many miles the gap widens and the spark needs more voltage to jump. Eventually the plug may misfire. Plugs are replaced at the interval in the manufacturer's schedule.
Diesels have glow plugs instead. When the engine is cold, the compressed air may not get hot enough to light the fuel reliably, so glow plugs heat the combustion chamber before and during starting. A failed glow plug shows up as hard cold starting and smoke. Neither kind of plug is a job for a learner: the ignition system's voltage can give a dangerous shock, and the work is done by trained technicians.
Read-through: the teaching steps
Two ways to ignite
- Spark ignition (petrol): mixture ignited by the spark plug.
- Compression ignition (diesel): air compressed until hot; fuel injected and ignites by itself.
The four-stroke drawing on the lesson page shows where ignition happens – near the top of the compression stroke.
The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes. Inside a spark plug
- Terminal at the top receives the high-voltage pulse.
- Ceramic insulator keeps the voltage from leaking to the engine.
- Centre electrode and side electrode, separated by the gap.
- Thread and seat seal the plug into the cylinder head.
How plugs wear
Each spark removes a tiny amount of electrode metal. Over thousands of sparks the gap widens. A wider gap needs more voltage; when the system can no longer supply enough, the plug misfires. Deposits from oil or rich running can also foul a plug. Many modern plugs use hard-wearing electrode tips that last much longer.
Why misfires matter
Unburnt fuel from a misfiring cylinder goes into the exhaust, where it can overheat the catalytic converter. California's Air Resources Board explains that a blinking check engine light means a malfunction is happening that could damage the catalytic converter, so it needs service as soon as possible.
Glow plugs
Glow plugs are small electric heaters. Before a cold start the dashboard glow-plug lamp shows they are heating; once it goes out the engine is ready to start. Many modern diesels also keep them on briefly after starting to reduce smoke and noise. A failed glow plug means hard cold starting, rough running and smoke when cold.
Theory only
This lesson explains how plugs work. Ignition systems produce a voltage that can give a dangerous shock, and plug replacement is done by trained technicians following the manufacturer's procedure and torque data.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 11 min | Not assessed, self-checked |
| Worked examples and guided practice | 7 min | Marked by Classfern |
| Independent practice (three levels) | 8 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Servicing and maintenance lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- US Department of Energy, Alternative Fuels Data Center – How do gasoline cars work?
- US Department of Energy, Alternative Fuels Data Center – How do diesel vehicles work?
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.