Port and direct petrol injection – Motor Vehicle Theory motor mechanics lesson
Lesson 42 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Compare the two ways a modern petrol engine injects its fuel – into the inlet port or straight into the cylinder – and learn how the control unit sets the amount by timing how long each injector is open.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson explains how petrol injection works. Fuel injection systems, especially direct injection, operate at high pressure with flammable fuel: any work on them is for trained technicians only. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “If direct injection is more efficient, why do you think some manufacturers fit both port and direct injectors to the same engine?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the control unit changes the fuel pressure to change how much fuel is injected. In normal running the pressure is held steady; the amount is set mainly by pulse width – how long the injector is open.
- Thinking direct injection is simply port injection moved closer. It sprays into the cylinder itself, needs much higher pressure and an engine-driven high-pressure pump, and cools the charge as the fuel evaporates.
- Thinking a longer pulse width means a weaker mixture. Longer open time means more fuel, so a richer mixture for the same air.
Hands-on: Spray experiment with an adult: use a clean plant mister filled with water. Count how many squeezes it takes to fill a measuring spoon, then work out the volume per squeeze – the same idea as fuel per injection. Next, time a slow, steady rhythm of squeezes and work out what fraction of each second your finger is pressing: that is a duty cycle. Use only water. If you look at a real engine, do it only with a qualified adult, with the car parked, switched off and cold, and only look – never touch fuel pipes or injector connectors.
What you will learn
- I can describe where the fuel is injected in port injection and in direct injection.
- I can explain how a solenoid injector works and what pulse width means.
- I can explain why direct injection can allow a higher compression ratio, and its drawbacks.
- I can calculate injector duty cycle from engine speed and pulse width.
- I can calculate the fuel delivered per injection from an injector's flow rate.
Key words
- port fuel injection (PFI)
- Injecting petrol into the inlet port, just upstream of the inlet valve, where it mixes with the incoming air.
- direct injection (DI)
- Injecting petrol straight into the combustion chamber at high pressure.
- injector
- An electrically operated valve that sprays fuel when the control unit opens it.
- pulse width
- How long the injector is held open for each injection, usually a few milliseconds. Longer pulse width means more fuel.
- duty cycle
- The percentage of the available time that an injector is open.
The big ideas
The US Department of Energy explains that in a petrol car the fuel is injected into either the intake manifold or the combustion chamber, mixed with air, and lit by the spark plug. Those two places give the two main systems in use today: port fuel injection, where each cylinder's injector sprays into its inlet port, and direct injection, where the injector sprays straight into the cylinder.
fueleconomy.gov notes that with direct injection the cooler air in the cylinder allows a higher compression ratio, improving combustion efficiency; it lists a potential efficiency improvement of about 2% to 3%. Direct injection needs much higher fuel pressure and brings its own problems, so some engines use both systems.
In both, the engine control unit decides how much fuel to inject by how long it holds each injector open. This lesson explains the theory. It is not a repair guide: fuel injection systems, especially direct injection, run at high pressure and are for trained technicians only.
Read-through: the teaching steps
How an injector works
Most petrol injectors are solenoid valves. Inside is a coil of wire around a small needle or ball held shut by a spring. When the control unit switches current through the coil, the magnetic field lifts the needle and fuel sprays out of the tiny holes in the nozzle as a fine mist. When the current stops, the spring snaps it shut.
Because the fuel pressure is held steady, the amount of fuel depends on how long the injector is open – the pulse width. A cold start or heavy acceleration needs a longer pulse; cruising needs a shorter one.
Port fuel injection
In port injection, each injector sits in the inlet manifold and sprays at the back of the inlet valve. The fuel has time to evaporate and mix with the air before the charge enters the cylinder, so it forms an even mixture.
Modern systems are sequential: each injector is timed to its own cylinder's induction stroke. Fuel pressure is moderate (a few hundred kPa is typical), so the parts are simple and quiet. Spraying onto the inlet valve also keeps it washed clean of deposits.
Direct injection
In direct injection, the injector sits in the cylinder head and sprays into the combustion chamber. Because the fuel has to enter a cylinder that may already be compressed, it needs far higher pressure – often many times that of a port system. An engine-driven high-pressure pump, worked by a lobe on a camshaft, feeds a separate high-pressure rail.
As the fuel evaporates inside the cylinder it absorbs heat and cools the charge. Cooler charge is less likely to knock, so the engine can use a higher compression ratio or more turbo boost, giving better efficiency and power.
The drawbacks of direct injection
Direct injection is not perfect:
- Less time to mix: in some conditions small wet spots of fuel burn poorly and make particulates (soot). Many direct-injection petrol cars now have a petrol particulate filter.
- Dirty inlet valves: because no fuel washes over the inlet valves, oily vapour from the crankcase breather can bake on as carbon deposits.
- Cost and noise: the high-pressure pump and injectors are more complex and can tick audibly.
Some engines use dual injection: port injectors at light load (clean valves, good mixing) and direct injectors at high load (cooling, knock resistance).
Duty cycle
A four-stroke cylinder has one induction stroke every two revolutions, so each injector gets one chance per two revolutions:
time available = 2 × 60 ÷ rpm seconds.
At 3,000 rpm that is 2 × 60 ÷ 3,000 = 0.04 s = 40 ms. If the pulse width is 10 ms, the duty cycle is 10 ÷ 40 × 100 = 25%. At high speed and full load the duty cycle rises; engine designers make sure the injectors are big enough that it never reaches 100%.
How much fuel per injection?
Injectors are rated by flow rate at a stated pressure, for example in cm³ per minute. The fuel per injection is:
flow rate × pulse width (in the same time units).
An injector flowing 240 cm³/min held open for 5 ms delivers 240 ÷ 60,000 cm³ per ms × 5 ms = 0.02 cm³ – a droplet smaller than a raindrop. Real injectors take a fraction of a millisecond to open and close, so the control unit adds a small correction for this.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Fuel, ignition and emissions lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- US Department of Energy, Alternative Fuels Data Center – How do gasoline cars work?
- US Department of Energy and EPA, fueleconomy.gov – Advanced engine technologies
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.