Diesel injection: common rail – Motor Vehicle Theory motor mechanics lesson
Lesson 43 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out how a common rail system stores diesel at extremely high pressure and lets the control unit fire several precisely timed injections into each cylinder every cycle.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson explains how common rail diesel injection works. These systems hold fuel at pressures that can pierce skin and cause serious injury, even after the engine is switched off: any work on them is for trained technicians only. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Common rail systems made diesel engines much quieter. Why do you think a quieter engine was important for diesel cars to become popular?”
- Later: the homework, then the practice test.
Watch out for
- Thinking the injection pressure in a common rail system depends on engine speed. The rail stores fuel at the pressure the control unit chooses. That is the whole point of the design: pressure and timing are independent of speed.
- Thinking a diesel injects its fuel once per cycle. Common rail diesels often use pilot, main and post injections in a single cycle.
- Thinking a diesel leak is safe to touch once the engine is off. The rail can hold high pressure after switch-off, and a fine jet can pierce skin. Never feel for leaks; this work is for trained technicians.
Hands-on: Pressure and spray with an adult: use a clean garden hose with an adjustable nozzle, or a clean squeezy bottle of water. Compare a slow dribble with a fine, fast spray and notice how the fine spray makes much smaller droplets that spread wider – this is why diesel injection uses very high pressure. Then make a timeline strip for one cycle and mark pilot, main and post injections near top dead centre. Use only water and never point a spray at anyone. Do not go near a real diesel fuel system for this activity.
What you will learn
- I can name the main parts of a common rail diesel system and describe what each does.
- I can explain why diesel injection needs very high pressure.
- I can explain why modern diesels use pilot, main and post injections.
- I can calculate how many crankshaft degrees an injection lasts at a given engine speed.
- I can explain why high-pressure diesel systems are dangerous and are for trained technicians only.
Key words
- common rail
- A strong tube that stores diesel at very high pressure and feeds all the injectors, so pressure does not depend on engine speed.
- high-pressure pump
- An engine-driven pump that raises diesel from the low pressure of the supply to the very high pressure of the rail.
- rail pressure sensor
- A sensor that tells the control unit the pressure in the rail, so it can keep it at the value it wants.
- pilot injection
- A tiny injection just before the main one that starts combustion gently, reducing diesel knock and noise.
- piezo injector
- An injector worked by a stack of piezoelectric crystals that change length when a voltage is applied; it can open and close very quickly.
The big ideas
The US Department of Energy explains that in a diesel vehicle the fuel is injected into the combustion chamber and lit by the high temperature of the compressed air. To burn well, the fuel must be broken into extremely fine droplets that mix with the hot air within a few thousandths of a second. That needs very high injection pressure and very precise timing.
Older diesel pumps made the pressure for each injection separately, so pressure and timing were tied to engine speed. A common rail system separates the two jobs: a high-pressure pump keeps a shared rail full of fuel at the pressure the control unit chooses, and electrically controlled injectors open whenever, and as often as, the control unit decides. This allows several injections per cycle, which makes diesels quieter, cleaner and more efficient.
This lesson explains the theory. It is not a repair guide: common rail systems hold fuel at pressures that can cut through skin and cause serious injury, even after the engine stops. Work on them is for trained technicians only.
Read-through: the teaching steps
From tank to rail
A low-pressure lift pump (in the tank, or built into the high-pressure pump) draws diesel through a fine filter that also separates water, which would damage the precision parts.
The high-pressure pump, driven by the engine, then raises the pressure enormously and delivers fuel into the rail. Typical common rail pressures range from tens to hundreds of megapascals – hundreds to thousands of times atmospheric pressure. The rail acts as an accumulator: its volume smooths out pressure pulses so every injector sees almost the same pressure.
Controlling rail pressure
The control unit reads the rail pressure sensor and adjusts the pressure using a metering valve on the pump inlet, a pressure control valve on the rail, or both. It chooses a high pressure for high load (fine spray, fast mixing) and a lower pressure at idle (quieter running).
A pressure-limiting valve opens if the pressure ever rises dangerously high. Fuel not used by the injectors, including a small leak-off from each injector, returns to the tank through a return line.
The injectors
Common rail injectors are electrically controlled valves at the rail pressure. There are two main kinds:
- Solenoid injectors use a magnetic coil to release a small control valve; the rail pressure itself then lifts the needle.
- Piezo injectors use a stack of piezoelectric crystals that lengthen slightly when a voltage is applied. They react faster, allowing more, shorter injections.
The nozzle has several tiny holes, each far thinner than a pencil lead, aimed to spread the spray across the combustion chamber.
Several injections per cycle
Because the control unit can open the injector whenever it likes, one combustion event can use several injections:
- Pilot injection: a tiny amount just before the main one. It lights first, warming the chamber, so the main fuel lights smoothly with less diesel knock.
- Main injection: the fuel that makes the power.
- Post injection: a small late amount that can help burn soot or raise exhaust temperature to help aftertreatment such as the particulate filter.
The result is a diesel that is quieter and cleaner than older designs.
Timing in crankshaft degrees
Injection timing and duration are often described in degrees of crankshaft rotation. The crankshaft turns 360° each revolution, so at a speed of N rpm it turns 360 × N ÷ 60 degrees per second.
At 3,000 rpm that is 360 × 50 = 18,000° per second. An injection lasting 1 ms (0.001 s) therefore covers 18,000 × 0.001 = 18° of crankshaft rotation. At higher speed the same duration covers more degrees, so the control unit starts injection earlier.
High pressure is dangerous
A fine jet of fuel at common rail pressure can pierce the skin and inject fuel into the body – a fuel injection injury that needs urgent hospital treatment even if the wound looks tiny. The rail can stay at high pressure after the engine stops.
That is why technicians follow the manufacturer's procedure, use the right equipment and protective gear, and never feel for leaks with their hands. Leaking diesel also makes surfaces slippery and is a fire risk near hot exhaust parts. As a learner, study the theory only.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Fuel, ignition and emissions lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.