▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Overall gear ratio and road speed calculations – Motor Vehicle Theory motor mechanics lesson

Lesson 63 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Learn to work out overall gear ratio, road speed from engine speed, engine speed for a given road speed, tyre diameter from the sidewall size and the tractive force at the wheels.

Time
50 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson practises gear ratio, road speed and tractive force calculations, using typical values. Tyre size markings follow the manufacturer's owner's manual explanation. Tyre and wheel changes on a real vehicle must stay within the maker's approved sizes and be done by trained technicians. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why might a car maker choose a final drive ratio that gives slightly lower top speed but quicker acceleration?”
  4. Later: the homework, then the practice test.

Watch out for

  • Using the rim diameter as the wheel size. The tyre adds a sidewall at the top and bottom. Diameter = rim + 2 × sidewall.
  • Forgetting to change minutes to hours. rpm is per minute. Multiply metres per minute by 60, then divide by 1,000 for km/h.
  • Multiplying when finding wheel speed. Wheels turn slower than the engine: divide engine speed by the overall ratio.

Hands-on: Measure a bicycle wheel with an adult: mark the tyre and the ground with chalk, roll the bike one full turn in a straight line and measure the distance. Compare it with 2π × radius. Then count the teeth on the chainring and rear sprocket, work out the ratio, and calculate how far the bike goes for one turn of the pedals. Keep fingers away from the chain and spokes.

What you will learn

  • I can calculate overall gear ratio from gear and final drive ratios.
  • I can calculate road speed from engine speed, overall ratio and rolling radius, and work backwards.
  • I can calculate tyre diameter from a sidewall size and explain its effect on the speedometer.
  • I can calculate tractive force at the driven wheels.

Key words

overall ratio
Gear ratio × final drive ratio.
rolling radius
The distance from the wheel centre to the road when the tyre is loaded; slightly less than the unloaded radius.
rolling circumference
The distance the car travels in one turn of the wheel: 2π × rolling radius.
tractive force
The forward push of the driven tyres on the road.
aspect ratio
Sidewall height as a percentage of tyre section width, the "55" in 205/55 R16.

The big ideas

Engineers choose gear ratios so that a car can move off briskly, climb hills and cruise quietly. To check a design, they work out road speed for each gear at any engine speed, the engine speed needed for a given road speed, and the force the tyres push with.

These calculations bring together everything in this subject: gear ratio, final drive, tyre size and torque. Every one follows the drive from the engine to the road, dividing speed and multiplying torque at each reduction, then turning wheel rotation into distance using the tyre's circumference.

The figures here are typical engineering values for practice. Real vehicle data comes from the manufacturer.

Read-through: the teaching steps

  1. Overall ratio

    Overall ratio = gear ratio × final drive ratio.

    For example, fifth gear 0.8:1 with a 3.9:1 final drive gives 0.8 × 3.9 = 3.12:1. The engine turns 3.12 times for each turn of the wheels.

    EngineClutchGearboxPropeller shaftDifferentialTurning force
    How the turning force gets from the engine to the driven wheels (rear-wheel drive shown).
  2. Wheel speed and distance

    • Wheel speed (rpm) = engine speed ÷ overall ratio.
    • Rolling circumference C = 2π × rolling radius.
    • Distance per minute = wheel rpm × C.
    • Road speed in km/h = wheel rpm × C × 60 ÷ 1,000.
    • Road speed in mph = km/h ÷ 1.609.

    The rolling radius is the loaded radius, a little smaller than the unloaded tyre.

  3. Working backwards

    To find the engine speed for a given road speed, reverse the steps:

    1. Change the road speed to metres per minute (km/h × 1,000 ÷ 60). 2. Wheel rpm = metres per minute ÷ C. 3. Engine rpm = wheel rpm × overall ratio.

  4. Tyre size from the sidewall

    A size such as 205/55 R16 gives: section width 205 mm; aspect ratio 55, so sidewall height = 205 × 0.55 = 112.75 mm; R for radial construction; 16-inch rim = 406.4 mm. Overall diameter = rim + 2 × sidewall = 631.9 mm. (The tyre lesson covers the full marking, as explained in the maker's owner's manual.)

    205 / 55 R 16 91 VWidthin mmSidewall height% of widthRadialRim sizein inchesLoad indexSpeed rating
    Reading a tyre size code.
  5. Speedometers and tyre size

    The speedometer works from wheel or gearbox rotation. If a tyre with a larger diameter is fitted, each turn covers more ground and the car goes faster than the speedometer shows. Percentage difference = (new diameter ÷ old diameter − 1) × 100. Tyre size changes must stay within what the vehicle maker allows.

  6. Tractive force

    The torque at the wheels pushes on the road through the tyre's rolling radius:

    F = engine torque × overall ratio × drivetrain efficiency ÷ rolling radius

    In first gear the ratio is large, so F is large, which is what moving off and climbing need. In top gear F is smaller but the car can go faster.

The lesson, step by step

50 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task15 minNot assessed, self-checked
Worked examples and guided practice10 minMarked by Classfern
Independent practice (three levels)16 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Transmission and drivetrain lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.