▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Manual handling, slips and trips – Motor Vehicle Theory motor mechanics lesson

Lesson 7 of 131 in the Motor Vehicle Theory course (ages 16+)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Find out why lifting, carrying, slips and trips cause most workshop accidents, and how HSE's avoid–assess–reduce approach and simple physics make handling safer.

Time
40 minutes + 10 min homework
Course
Motor Vehicle Theory (ages 16+)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.

How to use this lesson

This lesson explains HSE's manual handling guidance and the physics of moments. The activity uses a ruler and a small bag of rice. Every answer is marked straight away with a worked explanation.

  1. Read what you will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think everyday hazards like slips and lifting cause more accidents than dramatic ones like fires?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking there is a legal weight that is always safe to lift. HSE says the law sets no specific weight limit; the risk depends on the task, the person, the load and the environment.
  • Thinking slips and trips are too minor to matter. HSE says they are among the most common causes of workshop accidents.
  • Thinking good technique alone solves manual handling. Avoiding the handling with aids and redesigning the task come first.

Hands-on: Use a ruler as a model: hold one end with a small bag of rice hanging 10 cm from your hand, then 30 cm away. Notice how much harder it is to keep the ruler level. Draw the two set-ups and calculate the moments (weight × distance). Then walk through a room at home or school and list any trip hazards you find.

What you will learn

  • I can define manual handling and explain why it causes so many injuries.
  • I can describe HSE's avoid, assess, reduce approach.
  • I can use moments to explain why loads should be held close to the body.
  • I can identify common slip and trip hazards in a workshop and their controls.
  • I can list the four areas considered in a manual handling assessment.

Key words

manual handling
Transporting or supporting a load by hand or bodily force: lifting, putting down, pushing, pulling, carrying or moving.
musculoskeletal disorder
An injury or condition of the muscles, joints, back or tendons, often caused by handling or repetitive work.
moment
The turning effect of a force: force × perpendicular distance from the pivot.
housekeeping
Keeping the workplace tidy and clean: floors clear, spills cleaned, tools stored.
mechanical aid
Equipment such as a trolley or lifting device that takes the load off the body.

The big ideas

When people imagine workshop accidents they picture falling vehicles and fires. But HSE says most accidents in motor vehicle repair involve slips, trips, falls and manual handling. Wheels, batteries, gearboxes and boxes of parts are heavy and awkward, floors get oily, and air lines snake across walkways.

HSE's approach to manual handling is a clear order: avoid hazardous manual handling so far as is reasonably practicable; assess the risk of any that cannot be avoided; and reduce the risk to as low as reasonably practicable. It notes that the law sets no specific weight limit – the risk depends on the load, the task, the person and the surroundings.

This lesson explains the science and the controls. It is theory for understanding: learners follow their workplace's training and supervision for any lifting.

Read-through: the teaching steps

  1. Why handling injures

    Lifting, twisting and carrying put large forces on the muscles and discs of the lower back. Injuries can happen in one awkward lift, or build up over months of repeated handling. HSE's tyre work guidance says manual handling accounts for nearly half of all tyre-related incidents reported.

  2. Avoid, assess, reduce

    HSE gives employers an order:

    • avoid hazardous manual handling so far as reasonably practicable – for example by using a wheel lifting aid, a trolley or a lift;
    • assess the risk of injury from any handling that cannot be avoided;
    • reduce the risk to as low as reasonably practicable.

    Where there is a risk, employers may also need to give information about a load's weight and where its centre of gravity is.

  3. Assessing a task

    Assessments commonly look at four areas, often remembered as TILE:

    • Task – twisting, stooping, reaching, distance carried, how often;
    • Individual – strength, health, training;
    • Load – weight, size, grip, stability;
    • Environment – space, floor surface, lighting, temperature.
  4. The physics: moments

    The lower back works like a pivot. A load held away from the body has a turning effect, or moment:

    moment = force × distance from the pivot.

    Double the distance and the moment doubles, so the back muscles must pull much harder. That is the science behind keeping loads close to the body.

  5. Slips and trips

    Common causes in a workshop:

    • oil, coolant and water on the floor;
    • air lines, cables and hoses across walkways;
    • parts and tools left on the floor;
    • poor lighting and changes in floor level, such as pit edges.

    The best controls tackle the source: fix leaks, use drip trays, route air lines overhead or along walls, keep walkways marked and clear, and clean spills straight away.

  6. Good housekeeping

    A tidy workshop is a safer workshop. Tools go back on boards, parts go on racks, waste goes in the right bins and floors are cleaned regularly. Housekeeping costs little and prevents the everyday accidents that HSE says are the most common.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Workshop safety lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.