Forced induction: turbochargers, superchargers and intercoolers – Motor Vehicle Theory motor mechanics lesson
Lesson 31 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out how a turbocharger or supercharger pushes extra air into an engine, why the air is cooled afterwards, and how to work out how much more air gets in.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson explains forced induction as theory. Turbochargers and exhaust parts reach very high temperatures and spin at very high speed: any work on them is for trained technicians only. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Many small cars now use a small turbo petrol engine instead of a larger non-turbo engine. What are the advantages and what could be the drawbacks?”
- Later: the homework, then the practice test.
Watch out for
- Using the boost (gauge) pressure directly in a gas calculation. Add atmospheric pressure first. 80 kPa of boost is about 180 kPa absolute, not 80.
- Thinking a supercharger gives free power. It is driven from the crankshaft, so it uses some of the engine's power. A turbo recovers energy from the exhaust instead, though it does add some resistance to the exhaust flow.
- Thinking an intercooler cools the engine. It cools the charge air on its way into the engine, to make it denser. The engine is cooled by its own cooling system.
Hands-on: Make a paper pinwheel and hold it in front of a hair dryer on its cool setting with an adult. The moving air spins the pinwheel, just as exhaust gas spins a turbine. Then draw a labelled flow diagram of a turbocharged engine: air filter → compressor → intercooler → inlet manifold → cylinders → exhaust manifold → turbine → exhaust. Mark where the air is hottest and where it is coolest. If you look at a real engine bay, do it only with a qualified adult, with the car parked, switched off and completely cold, and only look – turbochargers stay very hot long after the engine stops.
What you will learn
- I can explain why forcing more air into the cylinders lets an engine make more power.
- I can compare how a turbocharger and a supercharger are driven.
- I can convert between gauge and absolute pressure and calculate a pressure ratio.
- I can explain how an intercooler increases the density of the charge air.
- I can describe what a wastegate does and what turbo lag is.
Key words
- forced induction
- Pushing air into the cylinders at above atmospheric pressure, using a compressor.
- turbocharger
- A compressor driven by a turbine that is spun by the engine's exhaust gas.
- supercharger
- A compressor driven mechanically by the engine, usually by a belt from the crankshaft.
- boost pressure
- How far the pressure in the inlet manifold is above atmospheric pressure. It is a gauge pressure.
- intercooler
- A heat exchanger that cools the air after the compressor, so that more air fits into each cylinder.
- wastegate
- A valve that lets some exhaust gas bypass the turbine, to limit the turbocharger's speed and the boost pressure.
The big ideas
An engine's power depends on how much fuel it can burn each second, and that depends on how much air (really, how much oxygen) gets into the cylinders. A normally aspirated engine relies on atmospheric pressure to push air in. Forced induction uses a compressor to push in more.
fueleconomy.gov (US Department of Energy and EPA) describes turbochargers and superchargers as compressors that force additional air into the engine's cylinders. That lets a manufacturer use a smaller engine without losing power, and the site lists a potential efficiency improvement of about 2% to 6%.
Compressing air also heats it, and hot air is less dense, so many engines cool the air again in an intercooler. This lesson explains the theory. It is not a repair guide: turbochargers and exhaust parts get extremely hot and spin at very high speed, and work on them is for trained technicians only.
Read-through: the teaching steps
More air, more fuel, more power
Fuel needs oxygen to burn, roughly in a fixed proportion. So if twice the mass of air gets into a cylinder, about twice the fuel can be burned, and the engine can make much more power from the same size.
The mass of air in a fixed volume depends on its density. For a gas, density is proportional to absolute pressure ÷ absolute temperature (ρ ∝ p ÷ T). So there are two ways to get more air in: raise the pressure, and keep the temperature down.
The turbocharger
A turbocharger has two wheels on one shaft. The turbine sits in the exhaust and is spun by the hot exhaust gas. The compressor sits in the air intake and is spun by the same shaft.
The turbine uses energy that would otherwise leave down the exhaust, which is why turbos can improve efficiency. Turbo shafts spin extremely fast and run on bearings fed with engine oil; some are also cooled by engine coolant. Because the turbine needs exhaust flow to speed up, there is a short delay after the driver presses the pedal before full boost arrives: turbo lag.
The supercharger
A supercharger is driven directly by the engine, usually by a belt from the crankshaft. Because it turns whenever the engine turns, its boost arrives at once, with no lag.
The cost is that it takes power from the crankshaft to drive it, so less of the extra power reaches the wheels. Common types include positive-displacement (lobe or screw) blowers and centrifugal compressors.
Gauge and absolute pressure
Boost is usually given as a gauge pressure: how far above atmospheric pressure the manifold is. Gas calculations need absolute pressure:
absolute pressure = gauge pressure + atmospheric pressure.
Atmospheric pressure is about 100 kPa (101.3 kPa at sea level on a standard day). With 80 kPa of boost, the absolute manifold pressure is about 180 kPa, and the pressure ratio is 180 ÷ 100 = 1.8.
Why intercoolers help
Compressing air heats it. Air leaving a compressor can easily be 100 °C or more on a hot day. Hotter air is less dense, so part of the benefit of boosting is lost. Hot charge air also makes a petrol engine more likely to knock.
An intercooler (also called a charge-air cooler) is a radiator for the inlet air. It may be cooled by outside air or by a separate coolant circuit. Because density ∝ 1 ÷ T (in kelvin), cooling the air from 380 K to 320 K at the same pressure makes it 380 ÷ 320 = 1.19 times as dense: about 19% more air in each cylinder.
Controlling boost
If nothing limited it, a turbo would spin faster and faster as engine load rose, and the boost could become high enough to damage the engine. A wastegate is a valve that lets some exhaust bypass the turbine, limiting its speed. Many modern turbos use variable geometry instead: movable vanes change how the exhaust strikes the turbine, giving good boost at low speed and limiting it at high speed.
The engine control unit watches a boost pressure sensor and works the wastegate or vanes. Petrol turbo engines often have a lower compression ratio than similar non-turbo engines, to avoid knock under boost.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Engines lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.