Dual-clutch and continuously variable transmissions – Motor Vehicle Theory motor mechanics lesson
Lesson 59 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out how dual-clutch transmissions change gear in a fraction of a second, how belt-and-pulley CVTs give a stepless ratio, and how both compare with manual and conventional automatic transmissions.
- Time
- 45 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson compares dual-clutch, CVT and automated manual transmissions, using efficiency figures from the US Department of Energy's fueleconomy.gov (November 2026). It is theory only; work on these transmissions is for trained technicians. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “If you were buying a car for town driving, which transmission type would you choose, and why?”
- Later: the homework, then the practice test.
Watch out for
- Thinking a DCT has a torque converter. Most DCTs use two friction clutches instead of a converter.
- Writing the CVT ratio as drive ÷ driven. Like gears, ratio = driven ÷ drive. Small drive and large driven gives a low gear.
- Thinking a CVT has no losses. Belts, pulleys and the pump that clamps the belt all take some power.
Hands-on: Make a model CVT: cut two cones from card (or use two funnels) and mount each pair facing each other on a pencil so the gap can be changed. Run a rubber band between the two pencils. Move the cones closer on one pulley and apart on the other, and count how many turns of one pencil turn the other once. Make a table of the five transmission types with their good and bad points. If you look at a real car, do it only with a qualified adult, with the car parked, switched off and cold, and only look.
What you will learn
- I can describe how a dual-clutch transmission pre-selects and changes gears.
- I can explain how a CVT changes its ratio with variable pulleys.
- I can calculate CVT ratios, ratio spread and belt speed.
- I can compare manual, automated manual, dual-clutch, CVT and conventional automatic transmissions.
Key words
- dual-clutch transmission (DCT)
- A transmission with two clutches: one for the odd gears and one for the even gears.
- pre-selection
- Engaging the next gear on the idle shaft before the clutch handover.
- continuously variable transmission (CVT)
- A transmission whose ratio can take any value in its range, usually using variable pulleys and a belt or chain.
- ratio spread
- The lowest ratio divided by the highest ratio: a measure of a transmission's range.
- automated manual transmission (AMT)
- A manual-type gearbox whose clutch and gear changes are worked by actuators.
The big ideas
Engineers have looked for ways to combine the efficiency of a manual gearbox with the ease of an automatic. The US Department of Energy's fueleconomy.gov notes that manual transmissions are lighter and lose less energy than conventional automatics, and lists automated manuals and CVTs as advanced transmission technologies.
A dual-clutch transmission is essentially two manual gearboxes in one case, each with its own clutch, so one can be ready in the next gear while the other carries the drive. A CVT abandons fixed gears altogether: two pulleys with movable sides change their working diameters, and a steel belt or chain runs between them.
This is explanation for understanding, not a repair guide. These transmissions are complex and are serviced by trained technicians with the manufacturer's equipment.
Read-through: the teaching steps
Automated manuals
An AMT is a manual gearbox with actuators. fueleconomy.gov says it "does not require clutch actuation or shifting by the driver": a control unit decides when to shift, and a hydraulic system or electric motor works the clutch and selectors. It gives a potential efficiency improvement of 7% (fueleconomy.gov), but there is a pause in drive during each shift, like a manual.
Dual-clutch layout
A DCT has two input shafts, one inside the other. Clutch 1 drives the odd gears (1, 3, 5, 7); clutch 2 drives the even gears (2, 4, 6) and often reverse. Each shaft has synchromesh selectors worked by actuators. Clutches may be dry (in air) or wet (running in oil for cooling and higher torque).
Gear ratio = teeth on the driven gear ÷ teeth on the driving gear = 30 ÷ 10 = 3 to 1. A DCT gear change
In third gear, clutch 1 is applied and clutch 2 is open. The control unit pre-selects fourth on the even shaft. When it is time to change, clutch 1 releases as clutch 2 applies. The handover takes a fraction of a second and drive is never fully interrupted. To change down, the lower gear is pre-selected instead.
The CVT principle
Each CVT pulley is two cones facing each other. Moving the cones together pushes the belt outwards to a larger working radius; moving them apart lets it run lower.
- Ratio = driven pulley radius ÷ drive pulley radius.
- Low ratio: small drive radius, large driven radius.
- High ratio (overdrive): large drive radius, small driven radius.
fueleconomy.gov says this gives "an infinite number of engine/wheel speed ratios".
CVT benefits and limits
fueleconomy.gov lists smooth acceleration, no gear-change jolt, no frequent downshifting on hills and better fuel efficiency, with a potential improvement of 6%. Limits: belts and chains can only carry so much torque, and some drivers dislike the engine sound staying constant while the car speeds up, so many CVTs imitate stepped "gears".
Many hybrids use a different idea, a power-split device built from epicyclic gears and motors, which also gives a stepless ratio.
Comparing the types
- Manual: light, efficient, driver works the clutch.
- AMT: manual efficiency without a clutch pedal; pause in drive at shifts.
- DCT: very fast shifts, efficient; more complex.
- Conventional automatic: smooth, strong torque multiplication from the converter; more losses unless locked up.
- CVT: stepless and smooth; torque limits.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Transmission and drivetrain lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.