Automatic transmissions: epicyclic gears and control – Motor Vehicle Theory motor mechanics lesson
Lesson 58 of 131 in the Motor Vehicle Theory course (ages 16+)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out how epicyclic (planetary) gear sets give several ratios without sliding any gears, how clutches and brakes choose them, and how the control unit decides when to change gear.
- Time
- 50 minutes + 10 min homework
- Course
- Motor Vehicle Theory (ages 16+)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only. Rules and values on this page are given as of November 2026. Always check the current official source (GOV.UK and the DVSA MOT inspection manual) before relying on them.
How to use this lesson
This lesson explains epicyclic gearing and automatic transmission control, with ratio calculations. It is theory only; automatic transmission work is for trained technicians. Every answer is marked straight away with a worked explanation.
- Read what you will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why might a manufacturer choose an eight-speed automatic over a six-speed one? What would it cost them?”
- Later: the homework, then the practice test.
Watch out for
- Thinking automatic gears slide in and out of mesh. All epicyclic gears are always in mesh. Clutches and brakes choose which members are held or driven.
- Forgetting the "+1" in the reduction formulas. With the carrier as output, ratio = 1 + (held-side teeth relationship). Only the reverse case (carrier held) has no +1.
- Thinking P (park) is enough on its own on a slope. The parking pawl is a small part; the parking brake should also be applied.
Hands-on: Build a paper epicyclic set: cut a large ring with marks for 60 "teeth", a sun disc with 20 marks and two planet discs with 20 marks, and pin them on card. Hold the ring with your thumb and turn the sun one full turn; see how far the carrier (a strip joining the planet centres) moves. Check it is about a quarter turn (1 + 60 ÷ 20 = 4). If you look at a real car, do it only with a qualified adult, with the car parked, switched off and cold, and only look.
What you will learn
- I can name the parts of an epicyclic gear set.
- I can work out which member to hold or drive for reduction, direct drive, overdrive and reverse.
- I can calculate epicyclic ratios from tooth numbers.
- I can describe how hydraulics and a control unit apply the clutches and brakes.
Key words
- epicyclic gear set
- A sun gear, planets on a carrier and an annulus, all in constant mesh. Holding or driving different members gives different ratios. Also called a planetary gear set.
- sun gear
- The central gear of an epicyclic set.
- annulus (ring gear)
- The outer gear with teeth on its inside, meshing with the planets.
- planet carrier
- The frame that holds the planet gears on pins.
- valve body
- A block of passages and valves that sends hydraulic pressure to the clutches and brakes.
The big ideas
A conventional automatic transmission does not slide gears in and out of mesh. Instead it uses epicyclic (planetary) gear sets in which all the gears are always meshed. By holding one member still and driving another, the same set gives a reduction, an overdrive, direct drive or reverse.
Multi-plate clutches and brake bands, worked by hydraulic pressure, do the holding and driving. A transmission control unit decides which ones to apply from signals such as road speed and accelerator position. Modern automatics combine two or three gear sets to give many forward ratios.
This is explanation for understanding, not a repair guide. Automatic transmissions are complex and are serviced by trained technicians.
Read-through: the teaching steps
The epicyclic set
- Sun gear in the middle.
- Planet gears on pins in a carrier, meshing with the sun.
- Annulus (ring gear) around the outside, meshing with the planets.
To get drive, one member is the input, one is the output and one is held. Tooth numbers must fit: Za = Zs + 2 × Zp.
Gear ratio = teeth on the driven gear ÷ teeth on the driving gear = 30 ÷ 10 = 3 to 1. The four results
- Annulus held, sun in, carrier out: largest reduction, ratio 1 + Za ÷ Zs.
- Sun held, annulus in, carrier out: smaller reduction, ratio 1 + Zs ÷ Za.
- Sun held, carrier in, annulus out: overdrive (output faster than input).
- Carrier held, sun in, annulus out: reverse, ratio Za ÷ Zs.
- Any two members locked together: direct drive, 1:1.
- Nothing held: neutral.
Clutches and brakes
- A multi-plate clutch joins two rotating members (for example input to sun).
- A brake (a multi-plate brake or a band) holds a member to the casing.
- A one-way clutch can hold a member in one direction and freewheel in the other, which helps smooth some shifts.
Each is applied by fluid pressure on a piston and released by springs.
Hydraulic control
A pump, driven by the torque converter housing, makes fluid pressure. The valve body contains spool valves and passages that route this pressure to the right pistons. In modern transmissions, solenoid valves controlled electronically decide which circuits are fed and how fast pressure builds.
Electronic control
The transmission control unit reads road speed, engine speed, accelerator position, fluid temperature and the selector position. It picks the gear from stored shift maps and times each shift so one element releases as the next applies. It also controls the lock-up clutch. Faults are read with diagnostic equipment by a technician.
More gears
Linking two or three epicyclic sets, with members shared between them, gives six, eight or more forward ratios. More ratios keep the engine nearer its most efficient speed. The fueleconomy.gov transmission page notes that conventional automatics lose more energy than manual gearboxes; more ratios and lock-up are ways of closing that gap.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 15 min | Not assessed, self-checked |
| Worked examples and guided practice | 10 min | Marked by Classfern |
| Independent practice (three levels) | 16 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Transmission and drivetrain lessons · Motor Vehicle Theory course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
- US Department of Energy, Alternative Fuels Data Center – How do gasoline cars work?
- US Department of Energy and EPA, fueleconomy.gov – Advanced transmission technologies
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.