Wheel alignment: an introduction – Garage Basics motor mechanics lesson
Lesson 33 of 70 in the Garage Basics course (ages 11–16)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out what toe, camber and caster mean, why small angles make a big difference to tyre wear and steering, and work out toe from measurements.
- Time
- 40 minutes + 10 min homework
- Course
- Garage Basics (ages 11–16)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.
For parents: how to use this lesson
The foot and trolley activities show toe and caster without any car. Alignment on a real car is measured and set by a trained technician with special equipment. Every answer is marked straight away with a worked explanation.
- Read what your child will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why do you think hitting a kerb hard can change how a car drives afterwards?”
- Later: the homework, then the practice test.
Watch out for
- Thinking alignment is the same as wheel balancing. Alignment is about the angles the wheels are set at. Balancing is about spreading the weight evenly round each wheel.
- Thinking tiny angles cannot matter. A wheel set even slightly wrong is dragged sideways along every kilometre of road, which wears the tyre and can make the car pull.
- Mixing up toe-in and toe-out. Toe-in: the front edges point towards each other, like feet turned in. Toe-out: they point away.
Hands-on: Stand with your feet pointing slightly inwards (toe-in), then slightly outwards (toe-out), and walk a few steps each way: notice how your feet scuff. Then push a supermarket-style trolley or a toy with swivelling caster wheels with an adult and watch how the front wheels swing round to trail behind their pivots.
What your child will learn
- I can explain what wheel alignment means.
- I can describe toe, camber and caster.
- I can work out toe-in or toe-out from two measurements.
- I can link alignment problems to tyre wear and steering pull.
Key words
- wheel alignment
- The angles at which the wheels are set relative to the car and to the road. In the UK, setting the toe is often called tracking.
- toe
- Whether the front edges of a pair of wheels point slightly towards each other (toe-in) or away from each other (toe-out), seen from above.
- camber
- The tilt of a wheel seen from the front: top leaning in is negative camber, top leaning out is positive camber.
- caster
- The backward tilt of the steering axis seen from the side. It helps the steering return to straight ahead.
- self-centring
- The way the steering wheel returns to the straight-ahead position by itself after a corner.
The big ideas
When a car leaves the factory, each wheel is set at exact small angles to the car and the road. This is the wheel alignment. The angles are tiny, often fractions of a degree or a millimetre or two, but they matter a great deal. A wheel pointing even slightly the wrong way is dragged sideways along the road for every kilometre the car travels.
Three angles are the most important. Toe is whether the wheels point slightly in or out when seen from above. Camber is whether the wheels lean in or out at the top when seen from the front. Caster is the backward tilt of the steering pivot when seen from the side, which makes the steering want to return to straight ahead, like the front wheel of a supermarket trolley.
Alignment can be knocked out by hitting a kerb or a pothole, or by worn suspension parts. Signs include the car pulling to one side, a steering wheel that is not straight when driving straight, and uneven tyre wear. Alignment is measured and adjusted by trained technicians using special equipment and the manufacturer's data.
Read-through: the teaching steps
What alignment means
Each wheel can point slightly left or right, lean slightly in or out, and be mounted on a steering pivot that tilts. The manufacturer chooses these angles to give straight, stable running, good grip in corners and even tyre wear.
The main parts you can find on almost every car. Toe
Seen from above, if the front edges of the two front tyres are closer together than the rear edges, the wheels have toe-in. If they are further apart, the wheels have toe-out.
toe = distance between rear edges − distance between front edges
A positive answer means toe-in; a negative answer means toe-out.
Camber
Seen from the front, a wheel whose top leans towards the car has negative camber; leaning away is positive camber. A little negative camber helps the outer tyre grip in corners, when the body leans. Too much makes the inner edge of the tyre wear faster.
Caster
Seen from the side, the steering pivot is tilted so its top is further back than its bottom. The tyre touches the road behind the point where the pivot line meets the road, so it trails behind like a supermarket trolley wheel. That makes the wheels want to run straight and makes the steering self-centre after a turn.
Signs of poor alignment
- the car pulls to one side on a straight, level road
- the steering wheel is off-centre when driving straight
- tyres wear faster on one edge, or have a feathered (saw-tooth) feel across the tread
- the steering does not return to centre properly
How it is set
In a workshop, a technician uses alignment equipment with sensors or cameras on each wheel to measure the angles and compares them with the manufacturer's data. Toe is usually adjusted at the ends of the steering rods; some cars also allow camber and caster to be adjusted. The MOT inspection manual has a section on axles, wheels, tyres and suspension: the parts that hold each wheel at its angles.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 12 min | Not assessed, self-checked |
| Worked examples and guided practice | 8 min | Marked by Classfern |
| Independent practice (three levels) | 11 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Brakes, steering and suspension lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.