Valves and timing: letting gases in and out – Garage Basics motor mechanics lesson
Lesson 3 of 70 in the Garage Basics course (ages 11–16)
UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version
Find out how valves open and close at exactly the right moments, why they open a little early and close a little late, and how to work out how long a valve stays open.
- Time
- 45 minutes + 10 min homework
- Course
- Garage Basics (ages 11–16)
- You need
- Paper, a pencil and this page. No tools and no vehicle
- Marked
- Instantly, with explanations
Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.
For parents: how to use this lesson
A protractor and the formula duration = lead + 180 + lag are all that is needed. No real engine work is involved. Every answer is marked straight away with a worked explanation.
- Read what your child will learn and the big ideas.
- Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
- Finish with the exit ticket and the talk question: “Why might an engine designed for racing use different valve timing from one designed for a quiet family car?”
- Later: the homework, then the practice test.
Watch out for
- Thinking valves open exactly at TDC and BDC. Gases have inertia, so valves open early (lead) and close late (lag) to fill and empty the cylinder better.
- Measuring valve timing in camshaft degrees. Timing is normally given in crankshaft degrees. One cycle is 720° of the crankshaft but only 360° of the camshaft.
Hands-on: Draw a large circle for one crankshaft turn and mark TDC at the top and BDC at the bottom. On a second circle, mark the inlet valve opening 10° before TDC and closing 40° after BDC, and shade the open period. Measure the shaded angle with a protractor across both circles (remember the intake stroke runs from TDC to BDC). Does it match 230°?
What your child will learn
- I can explain how a cam, a valve and a spring work together.
- I can explain why the camshaft must stay exactly in step with the crankshaft.
- I can explain valve lead, lag and overlap.
- I can calculate how many degrees of crankshaft rotation a valve is open for.
Key words
- poppet valve
- The mushroom-shaped valve used in car engines. It is pushed open by a cam and closed by a spring.
- valve timing
- When each valve opens and closes, measured in degrees of crankshaft rotation.
- valve overlap
- The short time around top dead centre when the inlet and exhaust valves are both slightly open.
- timing belt
- A toothed belt (or a chain) that drives the camshaft from the crankshaft and keeps them in step.
- duration
- How long a valve stays open, measured in degrees of crankshaft rotation.
The big ideas
An engine has to breathe. Fresh air (and, in a petrol engine with port injection, fuel) must flow in, and burnt gases must flow out. The valves are the doors that control this, and the camshaft is the doorkeeper.
Each valve is shaped like a mushroom, with a flat head that seals against a seat in the cylinder head. A strong spring holds it shut. As the camshaft turns, an egg-shaped lobe pushes the valve open, then lets the spring close it again. The camshaft is driven from the crankshaft by a toothed belt, chain or gears, so the valves always open at the same point in the cycle.
Gases have mass, so they take time to start and stop moving. Engineers therefore open the valves a little before the piston reaches the end of its stroke and close them a little after. These timings are measured in degrees of crankshaft rotation. This is explanation for understanding: timing work on a real engine is done only by trained technicians using the maker's data.
Read-through: the teaching steps
Cam, valve and spring
The cam lobe pushes the valve down into the cylinder to open it. As the lobe turns past, the valve spring pulls the valve back up onto its seat to close it. The shape of the lobe decides how far the valve opens and for how long. Find the inlet and exhaust valves at the top of each cylinder in the drawing on the lesson page.
The four-stroke cycle: intake, compression, power, exhaust. The crankshaft turns twice for the four strokes. Keeping in step
The camshaft turns once for every two turns of the crankshaft. The timing belt or chain has teeth so it cannot slip. If it were one tooth out, the valves would open at the wrong moment and the engine would run badly. In some engines a broken belt lets pistons hit open valves, which is why makers give a replacement interval in the service schedule.
Measuring in degrees
One turn of the crankshaft is 360°. Each stroke is 180°. Valve timing is given as degrees before or after top dead centre (TDC) or bottom dead centre (BDC).
- One cycle = 720° of crankshaft rotation
- One stroke = 180°
Opening early, closing late
The inlet valve opens a little before TDC (valve lead), so it is already open as the piston starts down. It closes a little after BDC (valve lag), because the moving air keeps flowing in for a moment. The exhaust valve opens before BDC, near the end of the power stroke, and closes just after TDC.
Overlap
Around TDC at the end of the exhaust stroke, the exhaust valve has not quite closed and the inlet valve has just opened. This is valve overlap. The outgoing exhaust helps to draw the fresh charge in. Too much overlap can make an engine idle roughly.
Calculating duration
Duration = lead + 180° + lag.
Example: an inlet valve opens 10° before TDC and closes 40° after BDC. Duration = 10 + 180 + 40 = 230°. Many modern engines can change their valve timing while running, to suit low and high speeds, and many have four valves per cylinder to help the engine breathe.
The lesson, step by step
| Part | Time | How it is checked |
|---|---|---|
| Starter: warm up | 4 min | Marked by Classfern |
| Teaching and hands-on task | 14 min | Not assessed, self-checked |
| Worked examples and guided practice | 9 min | Marked by Classfern |
| Independent practice (three levels) | 13 min | Marked by Classfern |
| Exit ticket and talk question | 5 min | Marked by Classfern, self-checked |
Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.
The lesson
It runs here on the page. No sign-up and no names – progress is kept only in this browser.
Homework
About 10 minutes: 6 questions and a one-line reflection, all marked instantly.
More practice
More Engines and fuel lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department
Sources and curriculum
Facts in this lesson were checked against:
Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.