▶ TrainingGet Pro
All tools & lessonsAll toolsAllGet the appApp
Learning departments Music, Maths, Cookery, Programming and Art are open – explore →

Tyre wear patterns: what they tell you – Garage Basics motor mechanics lesson

Lesson 46 of 70 in the Garage Basics course (ages 11–16)

UK version. UK spelling and words (tyre, petrol, bonnet) and UK rules such as the MOT. · US version

Learn to read a tyre like a detective: each wear pattern points to a likely cause, from wrong pressure to poor alignment.

Time
40 minutes + 10 min homework
Course
Garage Basics (ages 11–16)
You need
Paper, a pencil and this page. No tools and no vehicle
Marked
Instantly, with explanations

Education and interest only. Classfern teaches motor mechanics as a school subject. It is not a training course or a qualification, and nothing here replaces an IMI or City & Guilds course, an apprenticeship or a qualified technician. Never work on a real vehicle without a qualified adult, the right protective equipment and safe equipment. High-voltage parts of electric and hybrid vehicles are for trained technicians only.

For parents: how to use this lesson

This is a look-only and drawing activity. If you ever see a bulge, cut or exposed cords on a tyre, have it checked by a technician before the car is driven. Every answer is marked straight away with a worked explanation.

  1. Read what your child will learn and the big ideas.
  2. Press Start the lesson below for the teaching, worked examples and practice (Getting started, On track or Challenge).
  3. Finish with the exit ticket and the talk question: “Why do you think a good technician looks at the old tyres before fitting new ones?”
  4. Later: the homework, then the practice test.

Watch out for

  • Thinking worn tyres just need replacing. If the cause (pressure, alignment, suspension) is not fixed, the new tyres will wear the same way.
  • Thinking both-edge wear means over-inflation. Both edges worn means under-inflation; centre wear means over-inflation.
  • Thinking a small bulge is only cosmetic. A bulge means the tyre's structure has failed. It is dangerous and must be checked at once.

Hands-on: Draw five tyre tread strips on paper and shade where each is worn: even, both edges, centre, one edge and cupped. Label each with its likely cause. Then, with an adult, look (without touching) at the tread of a parked, switched-off car and decide which drawing it is most like.

What your child will learn

  • I can match common tyre wear patterns to their likely causes.
  • I can explain why pressure, alignment and suspension affect where a tyre wears.
  • I can compare tread depths across a tyre and work out the difference as a percentage.
  • I can explain why damaged tyres must be checked by a qualified technician.

Key words

wear pattern
The shape of the wear across and around a tyre's tread.
shoulder
The outer edge of the tread, where it curves into the sidewall.
feathering
Tread blocks worn smooth on one side and sharp on the other, giving a saw-tooth feel. Often caused by wrong toe.
cupping
Scooped-out patches around the tread, often linked to worn suspension or unbalanced wheels. It is also called scalloping.
rotation
Moving tyres between wheel positions at set intervals, if the car maker recommends it, so they wear more evenly.

The big ideas

A tyre that is working properly wears evenly across its tread. When something is wrong, the tyre often shows it in the shape of its wear, long before the driver notices anything. Reading these patterns helps a technician find the cause, not just replace the tyre.

The common patterns are: both shoulders worn (too little pressure); the centre worn (too much pressure); one edge worn (camber or alignment out); feathered, saw-tooth blocks (wrong toe); scooped-out cups around the tyre (worn dampers or an unbalanced wheel); and a flat spot (a wheel that locked and skidded). Each points to a different cause.

Some damage matters even more than wear. The MOT inspection manual treats visible cords, deep cuts that reach the cords, and any lump, bulge or tear in the tyre structure as serious defects; a bulge is a Dangerous defect. Tyres are inspected and replaced only by trained technicians.

Read-through: the teaching steps

  1. Even wear is the goal

    A correctly inflated tyre on a well-aligned car, with good suspension and balanced wheels, wears evenly across the tread. Any other shape is a clue.

    Tread depthat least 1.6 mmCentral three-quarters of the treadTread blockGroove
    Tread depth is measured in the main grooves. For cars the legal minimum is 1.6 mm across the central three-quarters of the tread, all the way round.
  2. Pressure patterns

    • Both shoulders worn, centre fine: under-inflated. The soft tyre sags, so the edges carry the load.
    • Centre worn, shoulders fine: over-inflated. The hard tyre bulges in the middle.
  3. Alignment patterns

    • One edge worn (inner or outer): too much camber, or the wheel is out of alignment.
    • Feathering, where each tread block is smooth on one side and sharp on the other: wrong toe, so the tyre is dragged sideways as it rolls.
  4. Suspension and balance patterns

    • Cupping or scalloping, with scooped patches round the tyre: worn dampers let the wheel bounce, or the wheel is out of balance.
    • A flat spot: the wheel locked and skidded under hard braking.
  5. Comparing tread across the tyre

    A technician measures the tread at the inner edge, centre and outer edge. A big difference shows uneven wear.

    difference (%) = (deepest − shallowest) ÷ deepest × 100

  6. Damage, not just wear

    Cuts, bulges and visible cords are more urgent than wear. A bulge shows that the inside structure has failed and the tyre could burst. The MOT inspection manual notes that small regular ripples on a radial tyre's sidewall can be normal, and must be told apart from bulges by a trained tester.

The lesson, step by step

40 minutes in 5 parts
PartTimeHow it is checked
Starter: warm up4 minMarked by Classfern
Teaching and hands-on task12 minNot assessed, self-checked
Worked examples and guided practice8 minMarked by Classfern
Independent practice (three levels)11 minMarked by Classfern
Exit ticket and talk question5 minMarked by Classfern, self-checked

Make my lesson plan Opens this lesson in the free Lesson Plan Maker, filled in and ready to change, print or save.

The lesson

It runs here on the page. No sign-up and no names – progress is kept only in this browser.

Homework

About 10 minutes: 6 questions and a one-line reflection, all marked instantly.

More practice

More Wheels and tyres lessons · Garage Basics course · All motor mechanics practice tests · Motor Mechanics Department

Sources and curriculum

Facts in this lesson were checked against:

Our lessons and questions are our own. They are not written or endorsed by the DVSA, the IMI, City & Guilds, any college, testing agency or exam board.